Non-linear Modeling for Wireless Information and Power Transfer

This direction is merged into another direction: non-linear energy harvesting modeling. Its last version stays readable and citable here.

Version 1 of 163 papers76 conceptsfrozen 2026-10-04

In the quest for self-sustaining IoT networks, Simultaneous Wireless Information and Power Transfer (SWIPT) has emerged as a transformative paradigm. The core promise is simple: use the same radio frequency (RF) signal to deliver both data and energy. However, a significant gap exists between theoretical models and physical reality. Most early research relied on a "linear" assumption—the idea that harvested energy is directly proportional to received power.

As Bruno Clerckx and others have argued, this simplification is the "linearity trap." Real-world hardware components, specifically the rectifiers used to convert RF signals into direct current (DC), exhibit complex non-linear behaviors that fundamentally change how we should design wireless networks.

The Rectifier Bottleneck

To understand why the linear model fails, we must look at the hardware. An energy harvester typically consists of an antenna followed by a rectifier (often a diode-based circuit) and a low-pass filter. Xiao Lu and Dusit Niyato point out that the efficiency of this conversion is not constant; it can plummet from over 50% to less than 1% as the input signal weakens.

This non-linearity manifests in three distinct operational zones:

  1. The Sensitivity Threshold: Below a certain power level, the voltage is insufficient to turn on the diode. In this "dead zone," no energy is harvested at all, regardless of how long the signal is present.
  2. The Non-linear Transition: Once active, the efficiency varies wildly based on the signal's amplitude and waveform.
  3. The Saturation Region: At high power levels, the circuit reaches its physical limit. Any additional RF power is wasted as heat rather than converted to DC. Jae-Mo Kang and Il-Min Kim demonstrate that ignoring this saturation leads to overly optimistic performance predictions and suboptimal beamforming.

The Convex-Concave Nature of Energy Harvesting

A more precise way to visualize this is the "convex-concave" model. Ganggang Ma and Jie Xu describe the RF-to-DC conversion function as initially convex (at low power) and then concave (as it approaches saturation).

This shape has profound implications for how we transmit energy. In a linear world, it doesn't matter if you send 1mW for 10 seconds or 10mW for 1 second—the total harvested energy is the same. In the real, non-linear world, the 10mW "burst" is far more effective because it pushes the rectifier into a higher-efficiency operating point, whereas the 1mW "trickle" might fall below the sensitivity threshold. This is why Hang Yu and Yiwei Li suggest that bursty energy delivery is often superior for charging remote sensors.

Rethinking Resource Allocation

When we move away from linear assumptions, the optimization problems for beamforming and power splitting become significantly more difficult but also more rewarding.

Joint Beamforming and Power Splitting

In SWIPT, a receiver must decide how to split the incoming signal: some for the information decoder and some for the energy harvester. Qingjiang Shi showed that while linear models suggest simple ratios, non-linear models require dynamic adjustments. If the signal is too weak to harvest energy efficiently, the system should prioritize data; if the signal is strong enough to hit the saturation point, the excess should be diverted to the decoder.

Overcoming the Saturation Limit

To bypass the hardware's physical ceiling, researchers like Jae-Mo Kang have proposed using multiple EH circuits in parallel. By dynamically switching the number of active circuits based on the incoming power, the system can effectively "stretch" the saturation point, significantly improving the rate-energy tradeoff.

Time-Division Energy Beamforming

Instead of a steady stream of energy, Ganggang Ma and Jie Xu propose time-sharing different beamforming patterns. By concentrating energy into specific time slots, the transmitter can ensure that even distant users receive signals strong enough to trigger efficient hardware operation, mitigating the "doubly near-far problem" where distant devices are starved of power.

Beyond Radio Waves

The necessity of non-linear modeling extends to other forms of wireless power. In Simultaneous Lightwave Information and Power Transfer (SLIPT), Shunyuan Shang and Ziyuan Shi note that photovoltaic panels also exhibit non-linear responses under intense light or large signal swings. Similarly, in large-scale energy systems, Benjamin Flamm and Roy S. Smith have found that accounting for variable conversion efficiencies is critical for accurate energy arbitrage.

By embracing the non-linear reality of hardware, the field is moving from theoretical abstractions toward practical, deployable systems that can truly power the next generation of the Internet of Things.

Papers in this version

Showing 60 of 63 papers.

History & citationVersion 1 · 2026-10-04

Merged into another direction · Permanent link

View frozen version 1

Cite this direction

Latest version (a living page):

@misc{lacuna_non_linear_modeling_for_wireless_informa_d3b44d60,
  title = {Non-linear Modeling for Wireless Information and Power Transfer},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/non-linear-modeling-for-wireless-information-and-power-transfer/rdr_d3b44d60b2ff4254bff0ed52764efb14},
  note = {Latest version of a living research direction; cite a version for a fixed text. Accessed 2026-11-20},
}

This exact version (version 1, frozen text):

@misc{lacuna_non_linear_modeling_for_wireless_informa_d3b44d60_v1,
  title = {Non-linear Modeling for Wireless Information and Power Transfer},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/non-linear-modeling-for-wireless-information-and-power-transfer/rdr_d3b44d60b2ff4254bff0ed52764efb14/v/1},
  note = {Version 1, frozen 2026-10-04. Accessed 2026-11-20},
}