Channel Access Methods for RF-Powered IoT Networks: A Survey

Hang Yu, Lei Zhang, Yiwei Li, Kwan‐Wu Chin, Changlin Yang

Abstract

Many Internet of Things (IoT) networks with Radio Frequency (RF) powered devices operate over a shared medium, requiring specialized channel access protocols. Unlike conventional networks where devices have unlimited energy, in an RF-powered IoT network, devices must first harvest RF energy to transmit or receive data. This survey presents the first comprehensive review of contention-based and contention-free protocols in IoT networks with dedicated energy sources. It covers protocols based on Aloha, CSMA, polling, and dynamic TDMA, as well as successive interference cancellation. The survey highlights key challenges, provides qualitative comparisons, and identifies future research directions.

The Energy Causality Constraint

In traditional IoT deployments, battery life remains a critical bottleneck. Radio Frequency (RF) energy harvesting offers a sustainable solution by allowing devices to scavenge energy from radio signals. However, this introduces a unique constraint known as energy causality: a device cannot transmit data until it has harvested sufficient energy.

Standard channel access methods (e.g., Wi-Fi or cellular) assume devices are always "ready" to communicate. In an RF-powered network, a device might miss its transmission window because it is still in a charging phase. Furthermore, these networks suffer from the "doubly near-far problem." Devices located far from an energy source harvest less energy and simultaneously require more power to transmit data back to the gateway, leading to severe network unfairness.

Figure 2: Network architecture illustrating the separation of energy and information flows between HAPs, power beacons, and RF-powered devices.

MAC Protocol Families for RF-IoT

The survey categorizes Medium Access Control (MAC) protocols into two primary families based on how they manage the "harvest-then-transmit" requirement:

1. Contention-Based Protocols

  • Slotted Aloha: Devices transmit with a specific probability. Research focuses on optimizing frame sizes to balance collision minimization with harvesting time.
  • CSMA/CA: Devices "listen" before talking. Innovations include "Request for Energy" (RFE) packets and using local energy levels to dynamically determine backoff timers.

2. Contention-Free Protocols

  • Polling: A Hybrid Access Point (HAP) invites specific devices to transmit, often optimized for Age of Information (AoI) to ensure data freshness.
  • Dynamic TDMA: Time slots are assigned based on real-time energy levels and channel conditions rather than fixed schedules.
  • NOMA (Non-Orthogonal Multiple Access): This allows multiple devices to transmit simultaneously on the same frequency, using Successive Interference Cancellation (SIC) at the receiver to decode signals.

Receiver Architectures

Central to these protocols are receiver architectures like Time Switching, where a device alternates between charging and communicating, and Power Splitting, which divides the incoming signal to perform both tasks simultaneously.

Figure 3: The Time Switching architecture, showing the division of a frame into charging and information transmission phases.

Key Insights and Trade-offs

  • Energy-Aware Scheduling: Charging time must be treated as a schedulable resource. The HAP must strategically decide when to broadcast energy versus when to listen for data.
  • Throughput vs. Fairness: Maximizing total network throughput often starves distant devices. Proportional fairness models are essential to prevent node failure due to energy depletion.
  • Non-Linear Harvesting: While many models assume linear energy harvesting, real-world RF-to-DC conversion is non-linear. Research indicates that "bursty" energy delivery can be more efficient than steady, low-power streams.
  • Intelligence at the Edge: There is a growing shift toward using Reinforcement Learning (e.g., Q-Learning) to allow HAPs to adapt charging durations and frame sizes dynamically without perfect environmental models.

Future Research Directions

The authors identify several critical gaps in the current literature:

  • Advanced Modeling: Moving beyond linear EH models to reflect real-world circuit behavior.
  • New Technologies: Integrating Intelligent Reflecting Surfaces (IRS) to beamform energy toward low-power devices and using Graph Neural Networks (GNNs) to model complex interference.
  • Network Topology: Expanding research from single-hop setups to multi-hop networks where RF-powered relaying remains an open challenge.

Summary updated

Abstract

Many Internet of Things (IoT) networks with Radio Frequency (RF) powered devices operate over a shared medium. They thus require a channel access protocol. Unlike conventional networks where devices have unlimited energy, in an RF-powered IoT network, devices must first harvest RF energy in order to transmit or/and receive data. To this end, this survey presents the {\em first} comprehensive review of prior works that employ contention-based and contention-free protocols in IoT networks with one or more {\em dedicated} energy sources. Specifically, these protocols work in conjunction with RF-energy sources to deliver energy delivery or/and data. In this respect, this survey covers protocols based on Aloha, Carrier Sense Multiple Access (CSMA), polling, and dynamic Time Division Multiple Access (TDMA). Further, it covers successive interference cancellation protocols. It highlights key issues and challenges addressed by prior works, and provides a qualitative comparison of these works. Lastly, it identifies gaps in the literature and presents a list of future research directions.
BibTeX
@misc{yu2024channel,
  author = {Hang Yu and Lei Zhang and Yiwei Li and Kwan‐Wu Chin and Changlin Yang},
  title = {{Channel Access Methods for RF-Powered IoT Networks: A Survey}},
  year = {2024},
  eprint = {2404.14826},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2404.14826},
}
Figure