Abstract
Outdoor-to-indoor communications in millimeter-wave (mmWave) cellular networks have been one challenging research problem due to the severe attenuation and the high penetration loss caused by the propagation characteristics of mmWave signals. We propose a viable solution to implement the outdoor-to-indoor mmWave communication system with the aid of an active intelligent transmitting surface (active-ITS), where the active-ITS allows the incoming signal from an outdoor base station (BS) to pass through the surface and be received by the indoor user-equipments (UEs) after shifting its phase and magnifying its amplitude. Then, the problem of joint precoding of the BS and active-ITS is investigated to maximize the weighted sum-rate (WSR) of the communication system. An efficient block coordinate descent (BCD) based algorithm is developed to solve it with the suboptimal solutions in nearly closed-forms. In addition, to reduce the size and hardware cost of an active-ITS, we provide a block-amplifying architecture to partially remove the circuit components for power-amplifying, where multiple transmissive-type elements (TEs) in each block share a same power amplifier. Simulations indicate that active-ITS has the potential of achieving a given performance with much fewer TEs compared to the passive-ITS under the same total system power consumption, which makes it suitable for application to the size-limited and aesthetic-needed scenario, and the inevitable performance degradation caused by the block-amplifying architecture is acceptable.
Introduction
Millimeter-wave (mmWave) signals are the backbone of 5G and 6G, offering massive bandwidth. However, they have a major weakness: they are highly susceptible to blockage and attenuation by solid objects. A standard brick wall or tinted glass window can attenuate a signal by 28–40 dB, effectively killing indoor coverage from an outdoor base station (BS). This "penetration loss" is a primary bottleneck for outdoor-to-indoor (O2I) connectivity.
While Reconfigurable Intelligent Surfaces (RIS) are often proposed to fix coverage holes, traditional passive surfaces suffer from "multiplicative fading," where the total path loss is the product of the loss from the base station to the surface and the surface to the user. This often results in negligible performance gains unless the surface is massive. This paper introduces the Active Intelligent Transmitting Surface (active-ITS) as a solution that integrates power amplifiers to overcome these propagation barriers.
Active-ITS Architecture and System Model
The proposed active-ITS acts as a smart, active window. Unlike passive surfaces that only shift the phase of an incident wave, each transmissive-type element (TE) in an active-ITS magnifies the signal amplitude using integrated power amplifiers.
As illustrated in Figure 1, the active-ITS is deployed on the building boundary. The architecture of an active transmissive-type element includes a receiving patch, a phase-shifter and amplifier unit, and a refracting patch. To address the hardware cost and size constraints of individual amplifiers, the authors propose a block-amplifying architecture where multiple TEs share a single power amplifier, balancing performance with practical deployment feasibility.
Optimization Framework
The core technical challenge is a non-convex optimization problem: how to jointly design the precoding matrix at the BS and the transmissive coefficients (amplitude and phase) at the active-ITS to maximize the Weighted Sum-Rate (WSR).
The authors develop an efficient solution using:
- WMMSE Transformation: Converting the complex WSR problem into an equivalent Weighted Minimum Mean-Square Error (WMMSE) problem.
- Block Coordinate Descent (BCD) Algorithm: Iteratively optimizing the BS precoding, the ITS amplification factors, and the phase shifts until the system converges to a suboptimal solution in nearly closed-form.
Key Insights and Results
Simulations using the Saleh-Valenzuela channel model at 28 GHz demonstrate the following:
- Breaking Multiplicative Fading: By adding active gain at the surface, the active-ITS mitigates the product of path losses. This allows it to be much smaller than a passive counterpart; for instance, an active-ITS with 40 elements can outperform a passive-ITS with 60 elements under the same total power budget.
- Deployment Strategy: Unlike passive surfaces, active-ITS achieves its best performance when deployed closer to the indoor users.
- Hardware Trade-offs: The block-amplifying architecture provides a viable path to commercialization, showing that the performance degradation from sharing amplifiers across elements is acceptable compared to the hardware savings.
Conclusion
The active-ITS represents a significant step forward in solving the mmWave O2I coverage problem. By transforming building boundaries into active, refracting lenses, it ensures high-rate indoor connectivity. Future work will need to address the practicalities of Channel State Information (CSI) estimation and the impact of amplifier non-linearities in compact form factors.
Summary updated