Joint Precoding for Active Intelligent Transmitting Surface Empowered Outdoor-to-Indoor Communication in mmWave Cellular Networks

Xie Xie, Chen He, Xue Ma, Feifei Gao, Zhu Han

TL;DR

This paper introduces the Active Intelligent Transmitting Surface (active-ITS) as a solution for the notorious "penetration loss" problem in mmWave outdoor-to-indoor (O2I) communications. By equipping surface elements with power amplifiers, the authors demonstrate that active-ITS can overcome the "multiplicative fading" effect that plagues passive surfaces, achieving higher data rates with significantly fewer hardware elements.

What Problem Does This Paper Address?

Millimeter-wave (mmWave) signals are the backbone of 5G and 6G, offering massive bandwidth. However, they have a major weakness: they are terrible at passing through solid objects. A standard brick wall or tinted glass window can attenuate a signal by 28–40 dB, effectively killing indoor coverage from an outdoor base station.

While Reconfigurable Intelligent Surfaces (RIS) are often proposed to fix coverage holes, traditional reflective surfaces (IRS) require the transmitter and receiver to be on the same side. Transmissive surfaces (ITS) can act like a smart window, but passive versions suffer from "multiplicative fading"—where the total path loss is the product of the loss from the base station to the surface and the surface to the user. This often results in a negligible performance gain unless the surface is massive.

Methods

The authors propose an active-ITS where each transmissive-type element (TE) doesn't just shift the phase of the signal but also magnifies its amplitude using integrated power amplifiers.

1. Joint Precoding Optimization

The core technical challenge is a non-convex optimization problem: how do we jointly design the precoding matrix at the Base Station (BS) and the transmissive coefficients (amplitude and phase) at the active-ITS to maximize the Weighted Sum-Rate (WSR)?

  • WMMSE Transformation: They convert the complex WSR problem into an equivalent Weighted Minimum Mean-Square Error (WMMSE) problem, which is more mathematically tractable.
  • BCD Algorithm: They use a Block Coordinate Descent (BCD) approach, iteratively optimizing the BS precoding, the ITS amplification factors, and the phase shifts until the system converges.

2. Block-Amplifying Architecture

To address the high cost and size of giving every single element its own power amplifier, the authors propose a block-amplifying architecture. In this setup, multiple TEs share a single power amplifier. This reduces hardware complexity and power consumption, making the technology more viable for actual deployment on windows or walls.

Datasets

This is a theoretical and simulation-based study. No external real-world datasets were used. Instead, the authors evaluated their approach using:

  • Saleh-Valenzuela Channel Model: A standard model for mmWave propagation that accounts for limited scattering and cluster-based multipath.
  • Simulation Parameters: They modeled a 28 GHz carrier frequency, accounting for specific penetration losses for materials like tinted glass and brick.

Key Insights and Ideas

  • Breaking the Multiplicative Fading: By adding even a small amount of active gain at the surface, the "product" of path losses is mitigated. This allows the ITS to be much smaller than a passive counterpart while achieving the same performance.
  • Deployment Strategy: Unlike passive surfaces, which perform best when placed very close to either the transmitter or receiver, the authors found that active-ITS should be deployed closer to the users (indoors) to fully unleash its potential.
  • The "Active Lens" Intuition: The active-ITS essentially acts like a "concave lens" at the electromagnetic level, refracting and boosting signals as they pass through building boundaries.
  • Hardware Trade-offs: While element-wise amplification is ideal for performance, the "block-amplifying" architecture provides a "sweet spot" where hardware cost is significantly reduced with only a marginal, acceptable loss in data rate.

Key Results

  • Performance Gain: Simulations show that active-ITS significantly outperforms passive-ITS and "without-ITS" scenarios across various distances and power budgets.
  • Element Efficiency: An active-ITS with only 40 elements can outperform a passive-ITS with 60 elements under the same total system power consumption.
  • Convergence: The proposed BCD algorithm is shown to be highly efficient, typically converging to a stationary point within 10–20 iterations.
  • Robustness: The system maintains high performance even when the "refracting efficiency" (the amount of signal lost just by hitting the surface) is relatively low, as the active amplifiers can compensate for these losses.

Limitations and Future Work

  • CSI Requirements: The study assumes perfect Channel State Information (CSI) is available at the base station. In real-world mmWave environments, estimating the channel for a large number of ITS elements is a significant overhead challenge.
  • Static Environment: The model assumes a relatively static environment. Future work could explore how these surfaces handle highly mobile users or rapid blockages (e.g., people walking past the "smart window").
  • Thermal Noise: While the paper accounts for noise amplification at the active-ITS, the practical impact of amplifier non-linearities and heat dissipation in a compact "smart window" form factor remains to be explored.

Summary updated

Abstract

Outdoor-to-indoor communications in millimeter-wave (mmWave) cellular networks have been one challenging research problem due to the severe attenuation and the high penetration loss caused by propagation characteristics of mmWave signals. We propose a viable solution to implement the outdoor-to-indoor mmWave communication with the aid of an active intelligent transmitting surface (active-ITS), where the active-ITS allows the incoming signal from an outdoor base station (BS) to pass through the surface and be received by indoor users (UEs) after shifting its phase and magnifying its amplitude. Then, the problem of joint precoding of the BS and active-ITS is investigated to maximize the weighted sum-rate (WSR) of the system. An efficient block coordinate descent (BCD) based algorithm is developed to solve it with the suboptimal solutions in nearly closed-forms. In addition, to reduce the size and hardware cost of active-ITSs, we provide a block-amplifying architecture to partially remove the circuit components for power-amplifying, where multiple transmissive-type elements (TEs) in each block share the same power amplifier. Simulations indicate that active-ITS has the potential of achieving a given performance with much fewer TEs compared to the passive-ITS under the same total system power consumption, which makes it suitable for application to the space-limited and aesthetic-needed scenario, and the performance degradation caused by the block-amplifying architecture is negligible.
BibTeX
@article{xie2023joint,
  author = {Xie Xie and Chen He and Xue Ma and Feifei Gao and Zhu Han and Z. Jane Wang},
  title = {{Joint Precoding for Active Intelligent Transmitting Surface Empowered Outdoor-to-Indoor Communication in mmWave Cellular Networks}},
  journal = {IEEE Trans. Wireless Communications},
  year = {2023},
  doi = {10.1109/twc.2023.3247906},
}

Loading related content...

Figure