Shared Actuators for Multimodal Locomotion and Manipulation

This direction is split into other directions: multi-purpose limb utilization. Its last version stays readable and citable here.

Version 1 of 125 papers43 conceptsfrozen 2026-10-04

In traditional robotics, hardware follows a "one part, one purpose" philosophy. If a robot needs to walk, it has legs; if it needs to pick up an object, it has a dedicated arm; if it needs to fly, it has rotors. While intuitive, this modularity carries a significant "weight penalty." Every additional motor and linkage increases the system's mass, which in turn demands more power, reduces agility, and complicates the control stack.

A growing body of research is moving toward a more biological approach: actuator sharing. By repurposing existing locomotion hardware for secondary tasks—like using a leg as a finger or a propeller as a wheel—robots can achieve high-versatility "loco-manipulation" and multimodal mobility without the mechanical overhead of dedicated appendages.

The Weight Penalty Problem

The fundamental challenge in mobile robotics is the trade-off between capability and payload. As Zhi Zheng, Jin Wang, and their colleagues note, adding redundant actuators for different modes of movement (like flight and crawling) significantly degrades performance, especially in micro-scale vehicles where every gram counts.

Similarly, Seunghun Jeon and Jemin Hwangbo point out that mounting a dedicated robotic arm on a quadruped increases cost and complexity while reducing the robot's effective payload capacity. The solution is not to add more parts, but to make the existing parts do more.

The Leg as a Multi-Tool

The most prominent application of this idea is in legged robotics, where limbs are treated as generic actuators rather than fixed-role appendages. Richard M. Voyles and Juan P. Wachs describe this as "Intuitive Autonomy," where a single limb transitions dynamically between locomotion and manipulation based on the task.

This transition takes several forms:

  • Whole-Body Manipulation: Instead of "grasping," robots like those developed by Jeon et al. use their entire frame to re-pose heavy objects, using latent variable embeddings to "feel" the object's physical properties through contact.
  • Legs as Fingers: In the "Circus ANYmal" project, Fan Shi and Takahiro Miki demonstrated that a quadruped lying on its back can use its four legs as high-degree-of-freedom fingers to manipulate a yoga ball with extreme dexterity.
  • Functional Specialization: In hexapod robots, Xin Yang and Junkai Lu utilize limb redundancy to assign front legs as "pseudo-arms" for steering objects while the hind legs provide stable propulsion.

To manage these shifting roles, Xinghao Zhu and Jiuguang Wang introduced ReLIC, a framework that uses a binary masking system to assign limbs to either manipulation or locomotion tasks on the fly. This allows a robot like Spot to open a drawer with its foot while maintaining balance with its remaining legs.

Repurposing Flight Hardware

The principle of shared actuators extends beyond legs to aerial and aquatic propulsion. The goal is to use the high power-to-weight ratio of flight motors for ground-based tasks.

One approach is power-reuse mechanisms. Yi‐Kai Chen and Zhi Zheng developed the PerchMobi³, which repurposes its four ducted fans to provide both aerial thrust and the negative pressure required for wall adhesion. By using the same hardware for both, the robot can carry a payload exceeding 60% of its own weight—a feat impossible if it required a dedicated vacuum pump.

Other researchers focus on actuated-wheel-rotors. In the CapsuleBot and the Rollocopter (Tara Bartlett and Ali-akbar Agha-mohammadi), the primary flight actuators generate the thrust or torque needed for ground movement. By treating propellers as the drive system for passive wheels, these robots can roll on the ground using five times less energy than flight, without the weight of dedicated wheel motors.

Mechanical Reconfiguration and Docking

Actuator sharing also enables modularity. In the MobiDock system, Xuan-Thuan Nguyen and Hoang-Hiep Ly designed a robot that repurposes its primary locomotion motors to drive a mechanical docking screw. This allows independent robots to physically merge into a single bimanual platform. By using the high-torque locomotion motors for the connection, the system avoids the need for auxiliary docking actuators, maintaining a high power-to-weight ratio while enabling complex physical transformations.

Why It Works: The Shift to Generalist Hardware

The success of these systems suggests a shift in robotic design. Rather than building a "Swiss Army Knife" with many specialized tools, researchers are building "Generalist Actuators" that can be software-defined for different roles.

As Yifeng Gong and Guillaume Adrien Sartoretti argue in their review of legged manipulation, integrating these capabilities directly into locomotive limbs improves the payload-to-weight ratio and allows robots to interact with unstructured environments more naturally. Whether it is a cycloidal rotor acting as a wheel (Boyuan Deng) or a hexapod's leg acting as a gripper (Hyunchul Shim), the core intuition remains the same: the most efficient part is the one you already have.

Papers in this version

History & citationVersion 1 · 2026-10-04

Split into other directions · Permanent link

View frozen version 1

Cite this direction

Latest version (a living page):

@misc{lacuna_shared_actuators_for_multimodal_locomoti_18e27acf,
  title = {Shared Actuators for Multimodal Locomotion and Manipulation},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/shared-actuators-for-multimodal-locomotion-and-manipulation/rdr_18e27acf44d6401ab822cb73ff180e71},
  note = {Latest version of a living research direction; cite a version for a fixed text. Accessed 2026-11-19},
}

This exact version (version 1, frozen text):

@misc{lacuna_shared_actuators_for_multimodal_locomoti_18e27acf_v1,
  title = {Shared Actuators for Multimodal Locomotion and Manipulation},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/shared-actuators-for-multimodal-locomotion-and-manipulation/rdr_18e27acf44d6401ab822cb73ff180e71/v/1},
  note = {Version 1, frozen 2026-10-04. Accessed 2026-11-19},
}