Type test of LZDJ500T full hydraulic walking cable crane

Nianchun Deng, Shan Luo, Liuyi Wu, Xianhui Liu, Li Chen, Fulun WeiPrestress 2012 · DOI

Abstract

The cable hoisting crane is essential for constructing long-span suspension bridges. This paper details the development and type testing of the LZDJ500T, a full hydraulic walking cable crane designed for the Aizhai Bridge. The crane comprises a main truss beam, hydraulic walking and lifting systems, and a sophisticated control unit. To ensure safety before field deployment, a specialized ground-based test rig was developed to simulate bridge conditions. Results from static load and walking tests demonstrate that the crane's structural integrity and operational precision align closely with theoretical models, confirming its readiness for high-capacity bridge construction.

Introduction: The Challenge of Deep Canyon Construction

Constructing long-span suspension bridges over deep canyons, such as the 1,176-meter Aizhai Bridge in Hunan, presents significant logistical hurdles. Standard ground-based cranes cannot reach the necessary heights or handle the 200 to 500-ton steel truss segments required for such spans. Engineers overcome this by using cable-borne cranes that operate directly on the bridge's main cables. However, the extreme environment demands rigorous "type testing" to verify structural stability and mechanical reliability before the equipment is deployed hundreds of meters above ground.

Structural Design and Testing Methodology

The LZDJ500T utilizes a modular H-beam steel truss, allowing for adjustments to accommodate different cable spacings. Its defining feature is a hydraulic walking mechanism that uses a sequence of grippers and jacks to "walk" along the cables, providing superior stability compared to traditional rolling trolleys.

Structural layout and dimensions of the LZDJ500T crane.

To validate this design, researchers built a comprehensive ground-based test rig. This rig featured semi-circular tracks to simulate the main cables, with one side fixed and the other allowing for longitudinal and lateral movement to mimic real-world cable flexibility.

The ground-based test rig used for simulating bridge cable conditions.

Testing Protocol

  • Static Load Testing: Loads were applied incrementally up to 125% of the rated capacity (6250kN). Stress was measured at critical truss nodes using strain gauges, while mid-span deflection was monitored via high-precision laser rangefinders.
  • Walking Test: The hydraulic sequence for movement, braking, and position-holding was tested to ensure accurate operation and leak-free performance under load.

Key Insights and Experimental Results

A critical finding was the high degree of alignment between physical test data and Finite Element Analysis (FEA) predictions. For a 5000kN load, the measured deflection was 26mm, compared to a theoretical prediction of 23mm—a deviation of only 13%, which is excellent for machinery of this scale.

Performance Metrics

  • Load Capacity: The crane successfully managed its rated 5000kN load at side lifting points and 2400kN at center points.
  • Safety Margins: The maximum recorded stress was 127.3 MPa, well within the 233.1 MPa allowable limit for the Q345 steel used.
  • Structural Rigidity: The deflection-to-span ratio was 1/1038, significantly better than the 1/600 safety threshold.

Conclusion and Field Deployment

The successful type testing of the LZDJ500T paved the way for its deployment at the Aizhai Bridge. Two units were used to hoist all 69 steel truss segments, a task completed by August 2011. While the tests confirmed static and low-speed reliability, future work will focus on dynamic impact factors, such as high-altitude wind loads and vibration interactions between the crane and the main cables during the lifting process.

Summary updated

Abstract

Cable hoisting crane is a special equipment for hoisting the main beam of long span suspension bridge. The structure of full hydraulic walking cable crane is mainly composed of main truss beam, walking mechanism, power system, hydraulic system, control system and lifting system. In the process of being applied to the actual bridge, it relies on the main cable of the suspension bridge as the support to carry out the displacement walking and the fixation lifting. Before it is used in practical engineering, cable-borne crane should carry out type test, which includes static load test and walking test simulating real bridge hoisting condition. Two LZDJ5000T fully hydraulic walking cable hoist were developed for the main beam hoisting of Aizhai Bridge in Hunan Province. In order to carry out type test, a test device was designed for supporting and loading. The stress and mid-span deflection at the key point of the key section were measured during loading. The test results show that the displacement and deformation values of static load test are in good agreement with the theoretical values, and the performance of the loading system is good, the movement is accurate in walking test, and the performance of the whole machine is good.
BibTeX
@inproceedings{deng2012type,
  author = {Nianchun Deng and Shan Luo and Liuyi Wu and Xianhui Liu and Li Chen and Fulun Wei},
  title = {{Type test of LZDJ500T full hydraulic walking cable crane}},
  booktitle = {Prestress},
  year = {2012},
  doi = {10.59238/j.pt.2012.04.001},
}
Figure