A concise operation safety protection device in arm of tower crane and its parameter design

Xiao Lv, Lei Zhang, Ligui Kang, Zhuo Chen, Tonghai XieAdvances 2015 · DOI

Abstract

Operating and maintaining tower cranes presents significant fall risks for personnel walking along the horizontal jib (arm). This paper proposes a novel safety belt hanging protection device characterized by ease of installation and high safety. By tensioning a steel wire rope along the crane's arm, the system provides a continuous sliding anchor point. We discuss the mechanical constraints governing rope diameter, fixing plate thickness, orifice cross-sections, and bolt sizing. An integrated design process is presented, ensuring the structural integrity of the device under dynamic fall loads.

Introduction: The Challenge of Jib Maintenance

Maintaining a tower crane is a high-stakes task. Operators must frequently traverse the horizontal jib to inspect structural components or mechanical hazards. Current safety methods are often inadequate:

  1. Baskets or Carts: While these transport operators along the arm, unbalanced stresses can lead to catastrophic mechanical failure.
  2. Manual Climbing: Operators use traditional safety belts but often fail to re-hook them at every structural junction due to the tedious nature of the process. This "human factor" leads to fatal falls when workers choose efficiency over safety.

The objective of this research is to develop a "concise" protection device that is easily removable, does not hinder movement, and ensures continuous tethering.

Proposed Solution: The Sliding Anchor System

The proposed device consists of a high-strength steel wire rope tensioned along the upper chord of the crane jib. It is secured by fixing plates and tension bolts at either end.

Figure 1: Overview of the tower crane and the integrated safety protection device along the arm.

By buckling their safety belts onto this rope, operators can slide freely from the root to the tip of the arm without ever needing to unhook. This "sliding rail" concept eliminates the temptation to bypass safety protocols.

Methods and Parameter Design

The core of the paper focuses on the mathematical derivation of constraints for four critical components:

  • Wire Rope Diameter: Sized based on maximum tensile strength requirements.
  • Stationary Steel Plate Thickness: Calculated to withstand the load-bearing capacity of the welds.
  • Orifice Sectional Area: The dimensions of the opening where the rope is secured.
  • Tension Bolt Size: Engineered to withstand the sudden "jerk" of a falling human.

A critical innovation in this design is the application of a dynamic load factor. The authors calculate that a falling human creates a dynamic load ($W_1$) approximately 9.8 times their static weight ($W$). Including the static weight itself, the total design load ($P$) is established at approximately $10.8W$.

Key Results and Validation

The study provides crane manufacturers with ready-to-use formulas for sizing components based on the expected weight ($W$) of the operator:

  • Rope Area ($A_{rope}$): $> 0.0007563W$ (cm²)
  • Plate Thickness ($\delta$): $> 0.00054W$ (cm)
  • Bolt Area ($A_{bolt}$): $> 0.003176W$ (cm²)

To validate these theoretical models, a Finite Element Analysis (FEA) was performed using ANSYS. A 750N force (simulating an average person) was applied to the midpoint of the wire rope.

Figure 4: Finite Element Analysis (FEA) results showing the mechanical strain and deflection of the safety rope under load.

The simulation confirmed that the mechanical strain remained well within safe limits, proving that the proposed parameter design ensures structural integrity during a fall event.

Conclusion and Future Work

While the mechanical theory and 2D simulations are robust, several areas remain for future exploration. The current FEA uses a simplified two-dimensional model which may not fully capture lateral forces. Additionally, the long-term effects of environmental weathering and corrosion on the wire rope's reliability need further study. Finally, while the design addresses the "human factor" by simplifying belt usage, field testing is required to quantify improvements in worker compliance and operational speed.

Summary updated

Abstract

In view of the operation safety problem in arm of tower crane, a novel safe belts hanging protection device which has the characteristics of easily removed and high safety is proposed. Based on mechanical theory, constrains of rope diameter, fixed plate thickness, orifice cross section, the bolt size are discussed. Consequently, an integrated design process for parameters of protection device is proposed, and such method can ensure the safety of operating personnel.
BibTeX
@inproceedings{lv2015concise,
  author = {Xiao Lv and Lei Zhang and Ligui Kang and Zhuo Chen and Tonghai Xie},
  title = {{A concise operation safety protection device in arm of tower crane and its parameter design}},
  booktitle = {Advances},
  year = {2015},
  doi = {10.2991/icismme-15.2015.372},
}
Figure