The characteristics of shear wave splitting in the source region of the April 20, 2013 Lushan earthquake

Sha Liu, Jiansi Yang, Baofeng Tian, Yu Zheng, Xudong Jiang, Zhiqiang XuEarthquake 2013 · DOI

Abstract

This study investigates the crustal stress field in the source region of the $M_s$ 7.0 Lushan earthquake by analyzing shear wave splitting (SWS) in aftershock sequences. Using data from eight seismic stations, researchers found that fast-wave polarization predominantly aligns with local fault strikes. A significant "stress-relaxation" effect was observed, characterized by a temporal decrease in time-delays between split waves following the mainshock, providing insights into post-seismic crustal adjustment.

Introduction

Understanding the stress field within the Earth's crust is vital for seismic hazard assessment, yet direct measurement at depth is challenging. Shear wave splitting (SWS) offers a powerful diagnostic tool for this purpose. When a shear wave (S-wave) encounters rock containing stress-aligned microcracks, it bifurcates into two components: a "fast" wave polarized parallel to the cracks and a "slow" wave polarized perpendicular to them. By measuring the polarization direction of the fast wave and the time-delay between the two components, scientists can effectively map the orientation and intensity of the local stress field and the density of microcracks in the crust.

Methods and Data

The authors analyzed seismic data from the aftershock sequence following the $M_s$ 7.0 Lushan earthquake. The study utilized a robust local dataset comprising three permanent stations (BAX, MDS, TQU) and five temporary stations (L131–L135) deployed by the China Earthquake Administration.

Map of the study area showing the Lushan earthquake epicenter (red star), aftershock distribution (colored circles), and seismic station locations (black triangles).

From an initial catalog of over 5,000 aftershocks recorded between April 20 and May 2, 2013, the authors obtained 467 high-quality SWS measurements after rigorous filtering. Key methodological steps included:

  • Visual Inspection: The authors employed the manual visual inspection of particle motion diagrams to identify the exact arrival moments of fast and slow waves, ensuring high data fidelity.
  • Normalization: Time-delays were normalized by the length of the ray path (measured in ms/km) to allow for consistent comparison across different event distances.
  • Quality Control: Only data with high signal-to-noise ratios ($S/N > 8.0$) within a narrow "shear wave window" were used to avoid surface-induced distortions.

Key Insights and Results

Particle motion diagrams illustrating the visual inspection method used to identify fast and slow shear wave arrivals through orbital motion analysis.

Fault-Aligned Stress

At most stations, the fast-wave polarization was oriented Northeast (NE), matching the $207^\circ$ strike of the Dachuan–Shuangshi fault. This confirms that the local stress field is dominated by the regional tectonic movement of the Longmenshan fault zone. However, stations MDS and L131 exhibited complex, dual polarization directions (NE and SE), suggesting a localized stress field where intersecting faults cause microcracks to align in multiple directions.

Stress Relaxation in Real-Time

A significant finding was the temporal change in normalized time-delays, which ranged from 1.02 to 8.64 ms/km (averaging 3.89 ms/km). Station L134, located closest to the mainshock epicenter, recorded the largest time-delays, indicating the highest level of crustal anisotropy near the rupture point. Furthermore, at stations like BAX, a significant decrease in time-delay was observed in the days immediately following the mainshock (April 21–23). This is interpreted as a "stress-relaxation" effect, where intense pressure built up before the quake gradually dissipates as microcracks close or coalesce.

Conclusion

SWS analysis provides a dynamic view of how the Earth's crust responds to major seismic events. While manual visual inspection is subjective and labor-intensive, it remains a reliable method for characterizing anisotropy. Future work comparing these results with data from the 2008 Wenchuan earthquake and integrating borehole strain measurements could provide a more comprehensive 3D model of stress accumulation and release in the eastern margin of the Tibetan Plateau.

Summary updated

BibTeX
@inproceedings{liu2013characteristics,
  author = {Sha Liu and Jiansi Yang and Baofeng Tian and Yu Zheng and Xudong Jiang and Zhiqiang Xu},
  title = {{The characteristics of shear wave splitting in the source region of the April 20, 2013 Lushan earthquake}},
  booktitle = {Earthquake},
  year = {2013},
  doi = {10.1007/s11589-013-0034-z},
}
Figure