Ramjet Mode Combustion Test for a Dual-Mode Ramjet Engine Model with a Large Backward-Facing Step

Inyoung Yang, Kyungjae Lee, Yang-ji Lee, Chun-taek KimJournal of the Korean Society of Propulsion Engineers 2016 · DOI

Abstract

이중 모드 램젯 엔진 모델의 램젯 모드 연소 시험을 수행하였다. 엔진 모델은 흡입구, 연소기 및 노즐로 이루어졌다. 로켓 기반 복합 사이클 엔진에 사용하는 것을 전제로 큰 후향 계단을 가지는 형상을 선택하였다. 시험은 마하 5, 고도 24 km 조건에서 수행하였다. 연료를 카울면과 바닥면에 분산하여 다중 분사를 한 경우에 안정적인 연소를 달성할 수 있었다. 또한 연료 당량비를 카울면에서 0.5, 바닥면에서 0.5로 하여 총 당량비 1.0으로 한 경우에 연소기 내부에서 열질식이 발생하여 유동이 아음속으로 조성되는 램젯 모드로 운전됨을 확인하였다.

Introduction

Developing engines for hypersonic flight (Mach 5+) requires innovative designs that can handle a wide range of speeds. Rocket-Based Combined Cycle (RBCC) engines are a leading solution because they integrate rocket and ramjet functionalities into a single flow path. However, this integration introduces significant aerodynamic challenges. Specifically, RBCC engines require a "large backward-facing step" in the combustor to house rocket nozzles.

While necessary for the rocket phase, this step creates massive flow separation during ramjet operation, potentially preventing efficient fuel-air mixing. For a Dual-Mode Ramjet (DMR) to be effective, it must operate in "ramjet mode" (subsonic combustion) at lower supersonic speeds before transitioning to "scramjet mode" (supersonic combustion). This study investigates how to achieve stable ramjet-mode operation in a DMR model featuring this difficult large-step geometry.

Experimental Methodology

Ground tests were conducted at the Korea Aerospace Research Institute (KARI) scramjet test facility, simulating flight conditions at Mach 5 and an altitude of 24 km. The engine model consisted of a four-ramp intake, an isolator, a combustor with a 22mm backward-facing step, and a nozzle.

Figure 4: Schematic of the dual-mode ramjet engine model showing the intake, isolator, combustor with backward-facing step, and nozzle sections, along with pressure sensor locations (ib, cb, nb).

The researchers utilized gaseous hydrogen as fuel and tested two primary injection strategies: single-side injection (bottom wall only) and dual-side injection (split between the bottom and cowl walls). The engine was equipped with high-frequency static pressure sensors to monitor flow behavior, and Quasi-One-Dimensional (Q1D) modeling was employed to calculate internal Mach numbers and temperature distributions.

Results and Discussion

The Impact of Injection Strategy

The large 22mm step acted as a significant barrier to mixing. Initial tests using only bottom-wall injection resulted in weak combustion. The step caused the flow to accelerate and separate, effectively isolating the fuel from the air stream near the cowl.

Stable ramjet operation was only achieved when fuel was distributed to both the cowl and the bottom walls. By splitting the fuel 50/50 (an equivalence ratio of $\phi = 0.5$ on each side, totaling $\phi = 1.0$), the heat release was distributed across the entire combustor cross-section.

Figure 2: Wall static pressure traces from the combustor (cb) sensors showing the significant pressure rise and stabilization when the cowl and bottom injectors are activated.

Achievement of Ramjet Mode

As shown in the pressure traces, activating the dual-side injectors caused a significant spike in internal pressure. This pressure rise is indicative of thermal choking, where the heat release from combustion forces the supersonic incoming air to transition to subsonic speeds. Q1D analysis confirmed that under these conditions, the Mach number dropped to approximately 0.98 near the combustor exit, successfully establishing ramjet-mode operation despite the aerodynamic interference of the large step.

Conclusion

This research successfully demonstrated that stable ramjet-mode operation is possible in a DMR engine with a large backward-facing step, provided a symmetrical injection strategy is used. Distributing fuel between the cowl and bottom walls overcomes the mixing limitations imposed by the step geometry and enables the thermal choking necessary for subsonic combustion. Future work will focus on optimizing the step geometry to further enhance mixing and investigating the dynamic transition between ramjet and scramjet modes as flight speeds increase.

Summary updated

Abstract

이중 모드 램젯 엔진 모델의 램젯 모드 연소 시험을 수행하였다. 엔진 모델은 흡입구, 연소기 및 노즐로 이루어졌다. 로켓 기반 복합 사이클 엔진에 사용하는 것을 전제로 큰 후향 계단을 가지는 형상을 선택하였다. 시험은 마하 5, 고도 24 km 조건에서 수행하였다. 연료를 카울면과 바닥면에 분산하여 다중 분사를 한 경우에 안정적인 연소를 달성할 수 있었다. 또한 연료 당량비를 카울면에서 0.5, 바닥면에서 0.5로 하여 총 당량비 1.0으로 한 경우에 연소기 내부에서 열질식이 발생하여 유동이 아음속으로 조성되는 램젯 모드로 운전됨을 확인하였다. Ramjet mode combustion test was performed for a dual-mode ramjet engine model. The engine model consists of an air intake, a combustor and a nozzle. The combustor in the model has a large backward-facing step, designed to be used as a part of a rocket-based combined cycle engine. The test was performed at the flight speed of Mach 5 and the altitude of 24 km. Strong combustion was established only when the fuel was injected from both of the bottom-side and cowl-side wall. When the total fuel stoichiometric ratio was 1.0, distributed as 0.5 on the cowl side and 0.5 on the bottom side, the flow became subsonic at some portion in the combustor by thermal choking, i.e., ramjet mode was established for this condition.
BibTeX
@article{yang2016ramjet,
  author = {Inyoung Yang and Kyungjae Lee and Yang-ji Lee and Chun-taek Kim},
  title = {{Ramjet Mode Combustion Test for a Dual-Mode Ramjet Engine Model with a Large Backward-Facing Step}},
  journal = {Journal of the Korean Society of Propulsion Engineers},
  year = {2016},
  doi = {10.6108/kspe.2016.20.6.083},
}
Figure