Abstract
A numerical simulation is used to investigate the flow field characteristics of a three-dimensional over-under turbine-based combined cycle circular-to-rectangular transition exhaust nozzle when only the turbojet flowpath is in operation. The effect on the exhaust nozzle performance of there being a secondary injection on the ramp of the expansion section of the turbojet flow path is then examined. Finally, the impact of variations in the secondary injection design parameters is further investigated. The results show that a secondary injection can improve the exhaust nozzle's performance by reducing the axial force on the inner wall of the flow path. However, changes in flight status can undermine this improvement. Under the baseline operating condition, a secondary injection with a larger angle and close to the ramp outlet can produce a more significant improvement in nozzle performance. In this study, the axial thrust coefficient, lift and pitch moment of the nozzle can be improved by a maximum of 9.312%, 66.007% and 10.975%, respectively.
Introduction: The Challenge of Over-Under TBCC Nozzles
Hypersonic vehicles often utilize Turbine-Based Combined Cycle (TBCC) engines, which integrate a turbojet for low-speed flight and takeoff with a scramjet for high-speed hypersonic cruise. A significant design challenge lies in the exhaust system: the over-under configuration requires a single nozzle assembly to handle vastly different flow conditions.
Typically, these nozzles are optimized for the high-pressure, high-Mach exhaust of the scramjet. However, during subsonic or low-supersonic flight (Mach 0.29 to 3.0) when only the turbojet is active, the nozzle is geometrically "too large." This leads to over-expansion, where exhaust pressure drops below ambient levels before exiting. The resulting flow separation and backflow create massive drag and reduce thrust. This paper investigates "secondary injection"—active flow control that injects air into the nozzle—as a lightweight alternative to heavy mechanical variable-geometry systems to mitigate these losses.
Methodology
The researchers conducted 3D numerical simulations using ANSYS Fluent to solve the steady-state Reynolds-Averaged Navier-Stokes (RANS) equations. The RNG k-ε turbulence model was employed to accurately capture the complex shock-wave and flow separation interactions.
To ensure simulation accuracy, the model was validated against experimental data from Waithe and Deere (2003). The study focused on three primary design variables for the secondary injection:
- Mass flow rate of the injected air.
- Injection angle (θ) relative to the mainstream flow.
- Longitudinal location (Lsec) on the expansion ramp.
Key Insights and Flow Physics
- The Suction Effect: Simulations revealed that when only the turbojet operates, the idle scramjet flowpath acts as a cavity. This creates a suction effect that pulls the mainstream flow downward, inducing a complex, low-velocity backflow region that severely degrades efficiency.
- Pressure Balancing via Shock Waves: Secondary injection introduces a "separation shock wave" upstream of the injection point. This shock increases the static pressure on the nozzle's inner wall, effectively counteracting the negative axial forces (drag) caused by over-expansion.
- Geometric Sensitivity: The effectiveness of the injection is highly sensitive to its placement. The study found that increasing the injection angle (pointing it more upstream) and placing the injection site closer to the nozzle exit yielded the most significant performance gains.
Key Results
Under the baseline condition of Mach 0.8, secondary injection demonstrated substantial improvements across all key performance metrics:
- Axial Thrust Coefficient (Cfx): Increased by up to 9.312%.
- Lift (L): Improved by 66.007%, which is vital for maintaining the vehicle's aerodynamic trim during low-speed flight.
- Pitch Moment (M): Enhanced by 10.975%, contributing to better longitudinal stability.
The optimal configuration was identified as an injection angle of 135° (angled upstream) located at 0.75Lb (near the ramp outlet).
Conclusion and Future Outlook
Secondary injection proves to be a highly effective method for enhancing the performance of TBCC nozzles during the critical turbojet-only phase. By reducing the axial force on the inner walls, it recovers thrust and improves vehicle stability without the weight penalty of mechanical hinges.
However, the study also notes that these benefits are sensitive to the flight Mach number. Future research should focus on dynamic control systems that can adjust injection parameters in real-time as the vehicle accelerates, as well as optimizing the shape of injection ports to further exploit three-dimensional flow effects.
Summary updated