Design Study of a Dual-Mode Ramjet Engine with Large Backward-Facing Step

Inyoung Yang, Yang-Ji Lee, Kyungjae LeeJournal of the Korean Society of Propulsion Engineers 2015 · DOI

Abstract

Scaled model of a dual-mode ramjet engine with large backward-facing step, as a component of the rocket-based combined cycle engine, was designed. Design parameters were derived for this engine with the consideration of application for the rocket-based combined cycle engine. Design methodology was established for these design parameters. The design was partially verified through numerical study. Flow characteristics of the dual-mode ramjet engine with large backward-facing step was investigated experimentally. The design methodology for relevant design parameters established in this study was verified as feasible.

Introduction

The Rocket-Based Combined Cycle (RBCC) engine represents a significant advancement in high-speed propulsion, integrating rocket and air-breathing modes into a single flow path. A critical structural challenge in RBCC design is the inclusion of a large backward-facing step, necessary for housing rocket nozzles. This geometry introduces significant flow instability, as incoming air expands and accelerates rapidly (often exceeding Mach 3.4), complicating flame stabilization and ignition in the combustor. Standard scramjet designs often fail to account for this "big step," necessitating a new design methodology.

Design Methodology

To address these challenges, researchers at the Korea Aerospace Research Institute (KARI) established a design framework focusing on nine key parameters, including step height, combustor length, and injector placement. A central feature of the design is the Constant-area combustor (C-combustor) located immediately after the step. This section is designed to mitigate flow expansion and facilitate stable ignition by allowing the air to slow down sufficiently.

Schematic of the dual-mode ramjet engine components, highlighting the backward-facing step and injector locations.

The study also emphasized the need for vertical (90-degree) fuel injection to ensure adequate penetration into the high-speed air stream, particularly given the increased duct height required for rocket integration. Furthermore, the use of both floor and cowl (top wall) injectors was explored to optimize fuel-air mixing.

Experimental and Numerical Validation

The design was evaluated using a combination of 2D Computational Fluid Dynamics (CFD) and experimental testing in a hypersonic wind tunnel. CFD simulations utilized the $k-\omega$ SST turbulence model to predict behavior at Mach 5 (ramjet mode) and Mach 6 (scramjet mode). Experimental validation involved measuring wall static pressure across a scaled model to benchmark the numerical results and identify the onset of thermal choking.

Key Results

The investigation confirmed that the large step accelerates the flow significantly in the absence of combustion. However, the proposed design methodology proved effective in managing these conditions.

Comparison of experimental and calculated wall static pressure distributions (Ps/P0) along the engine length.

As shown in the pressure distribution plot, the CFD results closely align with the experimental data, validating the accuracy of the numerical model. The study further demonstrated that multi-point injection, specifically adding cowl-side injectors, significantly improves fuel-air mixing. At Mach 5, a total equivalence ratio of 1.4 successfully triggered thermal choking throughout the combustor, indicating a successful transition to efficient ramjet-mode operation.

Conclusion

This study successfully established and verified a design methodology for dual-mode ramjet engines with large backward-facing steps. The results highlight the importance of C-combustor geometry and optimized multi-point injection strategies in managing the complex flow fields inherent in RBCC systems. While 2D CFD provided a strong baseline, future work will involve 3D simulations and full combustion testing to account for corner vortices and further refine engine stability.

Summary updated

Abstract

로켓 기반 복합 사이클 엔진의 구성 요소로서 큰 후향 계단을 가진 이중 모드 램젯 엔진의 축소 모델을 설계하였다. 로켓 기반 복합 사이클 엔진에 적용하기 위해 설계 단계에서 고려하여야 하는 인자를 도출하였고 이 설계 인자에 대한 설계 방법을 정립하였다. 이러한 방법을 통하여 설계한 모델에 대하여 전산유체해석과 공력 시험을 수행함으로써 설계 검증을 일부 수행하고 큰 후향 계단을 가진 이중 모드 램젯 엔진의 유동 특성을 파악하였으며 이 연구에서 정립한 주요 설계 인자에 대한 설계 방법이 타당함을 확인할 수 있었다. Scaled model of a dual-mode ramjet engine with large backward-facing step, as a component of the rocket-based combined cycle engine, was designed. Design parameters were derived for this engine with the consideration of application for the rocket-based combined cycle engine. Design methodology was established for these design parameters. The design was partially verified through numerical study. Flow characteristics of the dual-mode ramjet engine with large backward-facing step was investigated experimentally. The design methodology for relevant design parameters established in this study was verified as feasible.
BibTeX
@article{yang2015design,
  author = {Inyoung Yang and Yang-Ji Lee and Kyungjae Lee},
  title = {{Design Study of a Dual-Mode Ramjet Engine with Large Backward-Facing Step}},
  journal = {Journal of the Korean Society of Propulsion Engineers},
  year = {2015},
  doi = {10.6108/kspe.2015.19.6.033},
}
Figure