Radio-frequency optomechanical characterization of a silicon nitride drum

Anna Pearson, Kiran E. Khosla, Matthias Mergenthaler, George Briggs, E. A. Laird, Natalia Ares

Abstract: On-chip actuation and readout of mechanical motion is key to characterize mechanical resonators and exploit them for new applications. We capacitively couple a silicon nitride membrane to an off-resonant radio-frequency cavity formed by a lumped element circuit. Despite a low cavity quality factor ($Q_E \approx 7.4$) and off-resonant, room-temperature operation, we are able to parametrize several mechanical modes and estimate their optomechanical coupling strengths. This enables real-time measurements of the membrane's driven motion and fast characterization without requiring a superconducting cavity, thereby eliminating the need for cryogenic cooling. Finally, we observe optomechanically induced transparency and absorption, crucial for a number of applications including sensitive metrology, ground state cooling of mechanical motion, and slowing of light.

Introduction

Mechanical resonators, such as the silicon nitride "drums" studied here, are essential components for high-precision sensors and emerging quantum technologies. However, characterizing their motion typically requires coupling them to high-frequency optical or microwave cavities. To achieve the necessary sensitivity, these setups often rely on superconducting materials that only function at cryogenic temperatures near absolute zero.

This requirement for cryogenic cooling creates a significant barrier: such systems are bulky, expensive, and significantly slow down the iteration cycle for device characterization. There is a clear need for "on-chip" methods that can actuate and read out mechanical motion at room temperature using simpler, more accessible electronics. This work demonstrates a simplified, room-temperature method to characterize silicon nitride mechanical resonators by coupling them to a low-quality-factor radio-frequency (RF) circuit.

Experimental Setup and Methods

The researchers utilized a lumped-element RF cavity to probe a 50 nm thick silicon nitride membrane. The membrane is partially metalized with aluminum and suspended over electrodes, forming a capacitor ($C_C$). This capacitor is integrated into an LC circuit (inductor-capacitor resonator) operating in the radio-frequency range at approximately 209 MHz.

Experimental setup and RF cavity characterization. (a) Schematic of the SiN membrane coupled to the RF readout circuit. (b) RF cavity resonance at $f_C \approx 209$ MHz. (c) Power spectra showing mechanical sidebands. (d) 2D plot of the driven mechanical response versus drive frequency.

As the membrane vibrates, the capacitance changes, which in turn shifts the resonance frequency of the RF cavity. This allows the authors to detect mechanical motion by monitoring the RF signal reflected from the circuit. Unlike traditional setups that strive for extremely high cavity quality factors ($Q$), this experiment uses a very "lossy" cavity ($Q_E \approx 7.4$). While counter-intuitive, this low $Q$ provides a large readout bandwidth, allowing for real-time monitoring of the membrane's motion. The membrane can be driven directly with an AC voltage or indirectly via radiation pressure using the RF cavity itself.

Mechanical Characterization and Real-time Readout

The system operates deep in the "unresolved sideband regime," meaning the cavity's linewidth is much wider than the mechanical frequency. Despite this, the authors successfully extracted single-photon coupling strengths ($g_0$) and mechanical quality factors. Because the RF cavity has such a broad bandwidth, the researchers could demodulate the signal to observe the membrane's physical displacement in real-time with a sensitivity of 0.4 pm/$\sqrt{\text{Hz}}$. This represents a tenfold improvement over similar previous room-temperature RF experiments.

Mechanical mode characterization and real-time readout. (a) Broad power spectrum identifying multiple mechanical modes. (b-d) Detailed views of specific modes, showing nearly degenerate peaks. (e) Real-time time-domain measurement of the membrane's driven motion.

The study identified multiple mechanical modes. The fundamental mode was found at ~78.6 kHz with a quality factor ($Q_0$) of approximately $1.6 \times 10^3$, while higher modes reached $Q$ factors up to $20 \times 10^3$. Interestingly, higher-order mechanical modes often appeared as "double peaks," indicating nearly degenerate modes likely caused by small asymmetries or imperfections in the fabrication of the square membrane. The single-photon coupling strength ($g_0/2\pi$) was measured at $1.9 \pm 0.1$ mHz, matching theoretical predictions from their circuit model.

Optomechanical Phenomena at Room Temperature

Beyond simple characterization, the researchers observed Optomechanically Induced Transparency (OMIT) and Absorption (OMIA). These are interference effects where a strong "drive" signal controls how a "probe" signal interacts with the system—effectively using RF waves to stop or enhance the mechanical response. Demonstrating that the membrane's motion can be actuated by radiation pressure alone provided a separate, independent measure of the system's optomechanical parameters.

Conclusion and Future Outlook

While operating at room temperature means the system is dominated by thermal noise—preventing the researchers from reaching the "quantum ground state" of motion—the platform offers significant advantages for rapid characterization and metrology. The low $Q$ factor, while limiting the overall strength of the optomechanical interaction compared to high-$Q$ microwave or optical cavities, is precisely what enables the high-bandwidth, real-time visibility demonstrated here.

This platform is ideal for applications in sensitive metrology and microwave-to-optical signal conversion. Furthermore, the ability to inject noise to effectively "heat" the mechanical mode opens doors for studying non-equilibrium thermodynamics in mechanical systems without the overhead of cryogenic infrastructure.

Summary updated

Abstract

On-chip actuation and readout of mechanical motion is key to characterize mechanical resonators and exploit them for new applications. We capacitively couple a silicon nitride membrane to an off resonant radio-frequency cavity formed by a lumped element circuit. Despite a low cavity quality factor (Q$_\mathrm{E}\approx$ 7.4) and off resonant, room temperature operation, we are able to parametrize several mechanical modes and estimate their optomechanical coupling strengths. This enables real-time measurements of the membrane's driven motion and fast characterization without requiring a superconducting cavity, thereby eliminating the need for cryogenic cooling. Finally, we observe optomechanically induced transparency and absorption, crucial for a number of applications including sensitive metrology, ground state cooling of mechanical motion and slowing of light.
BibTeX
@inproceedings{pearson2020radio,
  author = {Anna Pearson and Kiran E. Khosla and Matthias Mergenthaler and George Briggs and E. A. Laird and Natalia Ares},
  title = {{Radio-frequency optomechanical characterization of a silicon nitride drum}},
  booktitle = {Scientific},
  year = {2020},
  doi = {10.1038/s41598-020-58554-x},
}
Figure