Effect of micro-friction stir welding parameters on the mechanical properties and microstructure of 5052 aluminum thin sheets

Yeong‐Maw Hwang, Chengyu Lu, Renyu Chen

Abstract

This study examines micro-friction stir welding (µFSW) in aluminum alloys 5052-O and 5052-H32 using 0.8 mm thick sheets. The analysis evaluates weld heterogeneity across various process parameters through microstructural examination and tensile testing. Findings suggest that elevated rotational speeds increase heat input, facilitating grain growth within the stirred zone. A significant presence of equiaxed crystals (< 5 μm) was observed, with their frequency increasing alongside rotational speed. The yield strength joining efficiencies for 5052-O and 5052-H32 ranged from 136% to 156% and 103% to 112%, respectively. Tensile strength efficiencies reached up to 82% and 100%. The µFSW parameters were found to provide superior properties compared to conventional thick-plate friction stir welding.

Introduction

The rapid evolution of the "3C" sector (Computer, Communication, and Consumer electronics) has driven a demand for thinner, lighter components, such as those found in modern smartphones and laptops. Joining ultra-thin aluminum sheets (under 1 mm) presents significant manufacturing challenges. While traditional laser welding is common, it is often energy-intensive and can cause surface discoloration. Friction Stir Welding (FSW), a solid-state process, offers a high-quality alternative but requires careful scaling to the "micro" level (µFSW) to avoid defects like micro-cracks and uneven heat distribution in thin materials.

Materials and Methods

The study utilized 0.8 mm thick AA5052 aluminum in two conditions: annealed (5052-O) and strain-hardened (5052-H32). The chemical composition of the base material is detailed in Table 1.

Table 1: Chemical composition of 5052 alloy (wt.%)

A specialized µFSW setup was employed, featuring a 5 mm diameter shoulder and a 1.6 mm pin. Researchers compared smooth and screw-threaded pin geometries at rotational speeds between 5,000 and 10,000 rpm and traverse speeds ranging from 30 to 150 cm/min. Microstructural analysis was conducted using polarized light and scanning electron microscopy (SEM), while mechanical integrity was assessed via standard tensile testing.

Results and Discussion

Microstructural Evolution

Unlike the varied weld shapes seen in thick-plate FSW, µFSW of 0.8 mm sheets consistently produced a "basin-shaped" stir zone. This morphology is attributed to the high shoulder-to-thickness ratio, which concentrates frictional heat at the surface. The use of a screw-threaded pin was found to enhance material flow and increase the stirring area, leading to a more robust weld nugget.

Grain size was heavily influenced by the balance of heat input and dissipation. At 5,000 rpm, the rapid heat dissipation characteristic of thin sheets promoted the formation of ultra-fine equiaxed grains (under 5 μm). Conversely, increasing the speed to 10,000 rpm provided sufficient energy for grain growth, resulting in larger crystals.

Mechanical Properties and Joining Efficiency

The µFSW process demonstrated exceptional mechanical performance, particularly for the annealed 5052-O alloy, where the weld zone's yield strength significantly exceeded that of the base metal.

Comparison of µFSW results with conventional FSW literature for 5052 aluminum alloys

As shown in the comparison above, the 0.8 mm sheets achieved joint efficiencies that rival or exceed those reported for thicker plates. Specifically, 5052-O reached a tensile strength efficiency of 82%, while 5052-H32 achieved a near-perfect 100% efficiency.

Conclusion

Micro-friction stir welding is a highly effective method for joining ultra-thin 5052 aluminum sheets. By optimizing parameters such as pin geometry and rotational speed, researchers can achieve ultra-fine grain structures and joining efficiencies exceeding 100% for yield strength. These results indicate that µFSW is a superior alternative to conventional welding techniques for high-precision industrial applications in the electronics sector.

Summary updated

BibTeX
@inproceedings{hwang2023effect,
  author = {Yeong‐Maw Hwang and Chengyu Lu and Renyu Chen},
  title = {{Effect of micro-friction stir welding parameters on the mechanical properties and microstructure of 5052 aluminum thin sheets}},
  booktitle = {Research},
  year = {2023},
  doi = {10.21203/rs.3.rs-3466534/v1},
}
Figure