Impact of Electromagnetic Stirring on the Gas Metal Arc Welding of an MAR-M247 Superalloy

Yu‐Chih Tzeng, Chengyu Lu, RenYu ChenResearch 2021 · DOI

Abstract

In this paper, the impact of electromagnetic stirring (EMS) on the gas metal arc welding (GTAW) of an MAR-M247 superalloy was investigated. Results revealed that, without electromagnetic stirring, it was easy for carbides in the heat-affected zone (HAZ) of the weld bead to liquefy during welding, leading to weld bead cracks. Electromagnetic stirring refined the grains in the HAZ and the weld bead, leading to grain strengthening and subsequently resulting in the effective improvement in the hardness of the weld bead. In addition, electromagnetic stirring significantly facilitated the formation of the weld bead by the removal of large inclusions which in turn effectively improved crack resistance at the joint. It also accelerated the floating up of gas holes thereby reducing the generation of gas hole defects.

Introduction

MAR-M247 is a high-performance polycrystalline nickel-based superalloy essential to the aerospace and energy industries, particularly for the manufacturing of gas turbine blades. Designed to withstand extreme environments, it offers exceptional creep resistance and high-temperature stability. However, its complex chemistry makes it notoriously difficult to repair via welding. The primary challenge is "liquefaction cracking," where trace elements segregate at grain boundaries to form low-melting-point eutectic phases and brittle "Chinese script" carbides. During standard Gas Tungsten Arc Welding (GTAW), the intense heat causes these boundaries to liquefy and pull apart under thermal stress. Furthermore, the alloy's high viscosity often results in shallow weld beads plagued by gas holes and inclusions.

Methods

To address these challenges, researchers compared standard GTAW against GTAW assisted by Electromagnetic Stirring (EMS). The experimental setup involved an EMS device attached to the welding gun, controlled by a magnetic-field supply that allowed for adjustments in current and frequency. This external field interacts with the welding arc and the molten pool, inducing physical oscillation and stirring. The team performed Bead-on-Plate (BOP) tests and V-shaped butt welding using Turbalay@625 filler metal. Microstructural analysis was conducted using Optical Microscopy (OM), Scanning Electron Microscopy (SEM), and Energy-Dispersive Spectrometry (EDS), while real-time temperature changes were monitored via infrared thermometry.

Material Composition

Understanding the chemical makeup of MAR-M247 is fundamental to analyzing its welding behavior. The alloy contains a precise balance of elements designed for high-temperature strength, as detailed in the table below.

Chemical composition (wt.%) of the MAR-M247 superalloy used in the study.

Mechanisms of Improvement

The application of EMS introduces several critical improvements to the welding process. First, the magnetic field compresses the welding arc into a "meteor" shape, concentrating energy to improve penetration and narrow the weld bead. Second, the stirring action effectively breaks down large (50µm) "Chinese script" carbides into much smaller (10–15µm) particles, which significantly toughens the joint.

Thermal management is also greatly enhanced; EMS was found to lower the instantaneous temperature of the heat-affected zone (HAZ) from approximately 1600°C to 1113°C. By increasing the cooling rate, EMS prevents grain boundaries from lingering in the temperature range where liquefaction occurs. Additionally, the induced fluid flow helps float gas bubbles and large inclusions to the surface, reducing internal defects.

Key Results

The study's findings demonstrate that EMS-assisted welding significantly outperforms standard methods:

  • Crack Elimination: X-ray and SEM inspections confirmed that while standard GTAW produced significant hot cracks, EMS-assisted specimens were entirely crack-free.
  • Improved Geometry: The weld bead width was reduced from 6.91 mm to 5.61 mm, enhancing the weld bead formation coefficient.
  • Mechanical Properties: Hardness across the weld zones increased due to grain refinement (Hall-Petch strengthening). Tensile strength improved from 891 MPa to 930 MPa, and ductility (elongation) increased from 2.5% to 3.4%.
  • Fracture Behavior: SEM analysis of fracture surfaces showed a transition from brittle cleavage in standard welds to a tough, "dimpled" structure in EMS welds.

Conclusion

Electromagnetic Stirring proves to be a transformative technique for welding the MAR-M247 superalloy. By refining carbides, improving thermal management, and eliminating defects, EMS enables high-quality repairs that meet industrial standards. Future work should focus on optimizing magnetic field parameters for complex geometries and conducting long-term fatigue testing to ensure the durability of repaired components in operational environments.

Summary updated

Abstract

Abstract In this paper, the impact of electromagnetic stirring (EMS) on the gas metal arc welding (GATW) of an MAR-M247 superalloy was investigated. Results revealed that, without electromagnetic stirring, it was easy for carbides in the heat-affected zone (HAZ) of the weld bead to liquefy during welding, leading to weld bead cracks. Electromagnetic stirring refined the grains in the HAZ and the weld bead, leading to grain strengthening and subsequently resulting in the effective improvement in the hardness of the weld bead. In addition, electromagnetic stirring significantly facilitated the formation of the weld bead by the removal of large inclusions which in turn effectively improved crack resistance at the joint. It also accelerated the floating up of gas holes thereby reducing the generation of gas hole defects.
BibTeX
@inproceedings{tzeng2021impact,
  author = {Yu‐Chih Tzeng and Chengyu Lu and RenYu Chen},
  title = {{Impact of Electromagnetic Stirring on the Gas Metal Arc Welding of an MAR-M247 Superalloy}},
  booktitle = {Research},
  year = {2021},
  doi = {10.21203/rs.3.rs-902021/v1},
}
Figure