Elastic-plastic bearing capacity simulation of steel-concrete composite bridge tower

Shi Da Sun, Yang Liu, You‐Wu Wang, Kun Cheng, C.s. WangOpenalex Unknown 2024 · DOI · OpenAlex

Abstract

The tower of a cable-stayed bridge adopts the steel-concrete composite structure, which gives full play to the advantages of steel and concrete. In order to study the elastic-plastic bearing capacity of the steel-concrete composite bridge tower, ABAQUS was used to establish the finite simulation models of the tower section considering material nonlinearity. The elastic-plastic bearing capacity of the tower column was calculated and analyzed. Meanwhile, the influence of structural parameters such as the thickness of steel panels, the diameter of vertical bar, and the concrete strength on the bearing capacity of the tower column was discussed. The results show that the concrete and the steel are subjected to the joint force in the elastic stage. The structural design of the composite tower column has sufficient reservation on loading capacity, which can meet the requirements of the bearing capacity in the elastic stage. The optimization suggestions can improve the technical economy and construction efficiency.

Introduction: The Challenge of Composite Bridge Towers

As cable-stayed bridges scale to accommodate increasing traffic and longer spans, the structural integrity of bridge towers becomes paramount. Engineers are increasingly adopting steel-concrete composite structures to leverage the high compressive strength of concrete alongside the ductility and tensile strength of steel. However, the interaction between these materials under extreme "elastic-plastic" loading is complex. Specifically, how design parameters like steel plate thickness or concrete grade influence the ultimate bearing capacity remains a critical area of investigation.

Internal components of the steel-concrete composite bridge tower structure, showing panels, stiffeners, and reinforcement.

Methodology and Model Validation

This study utilized ABAQUS finite element analysis (FEA) software to simulate a bridge tower segment. The modeling approach incorporated:

  • Material Nonlinearity: A Concrete Damage Plasticity (CDP) model was used to capture the cracking and crushing behavior of concrete, while steel was modeled with its own yielding characteristics.
  • Element Selection: Solid elements were used for the concrete core and steel plates, with truss elements representing internal reinforcement bars.
  • Validation: The FEA model was benchmarked against physical experimental data from a composite column test. The simulation's predicted failure load matched the experimental results within a 2% margin of error, confirming the model's reliability for parametric studies.

Key Insights: Failure Modes and Material Synergy

The simulations revealed that in the elastic stage—the typical operating condition for these structures—the steel and concrete act synergistically as a single unit. As the load increases into the plastic range, the failure mode is characterized by local "bulging" of the outer steel plates caused by the expansion of the compressed concrete core.

Comparison of failure modes between the physical experimental test (a) and the FEA Mises stress simulation (b).

Parametric Analysis Results

The study conducted a parametric analysis to quantify the impact of various design choices on the tower's ultimate bearing capacity:

  • Concrete Strength: This was identified as the most critical factor. Upgrading from C50 to C60 concrete increased the ultimate bearing capacity by 19.3%.
  • Reinforcement Diameter: Reducing the vertical bar diameter from 40mm to 25mm resulted in a 6.7% decrease in capacity.
  • Steel Plate Thickness: Surprisingly, reducing the outer plate thickness from 16mm to 12mm had a minimal impact, reducing capacity by only 2.5% and showing negligible effect on initial stiffness.

Conclusion and Future Directions

The findings suggest that current composite tower designs possess significant safety margins, with stresses remaining well within the elastic range under standard design loads. Optimizing concrete strength offers the most efficient path to increasing structural capacity.

Future research should expand beyond axial compression to include combined loading scenarios (bending and torsion) and long-term durability factors such as concrete creep and steel corrosion over the structure's intended lifespan.

Summary updated

Abstract

The tower of a cable-stayed bridge adopts the steel-concrete composite structure, which gives full play to the advantages of steel and concrete. In order to study the elastic-plastic bearing capacity of the steel-concrete composite bridge tower, ABAQUS was used to establish the finite simulation models of the tower section considering material nonlinearity. The elastic-plastic bearing capacity of the tower column was calculated and analyzed. Meanwhile, the influence of structural parameters such as the thickness of steel panels, the diameter of vertical bar, and the concrete strength on the bearing capacity of the tower column was discussed. The results show that the concrete and the steel are subjected to the joint force in the elastic stage. The structural design of the composite tower column has sufficient reservation on loading capacity, which can meet the requirements of the bearing capacity in the elastic stage. The optimization suggestions can improve the technical economy and construction efficiency
BibTeX
@inproceedings{sun2024elastic,
  author = {Shi Da Sun and Yang Liu and You‐Wu Wang and Kun Cheng and C.S. Wang},
  title = {{Elastic-plastic bearing capacity simulation of steel-concrete composite bridge tower}},
  booktitle = {Openalex Unknown},
  year = {2024},
  doi = {10.1201/9781003483755-437},
}
Figure