Study on the Force Transmission Mechanism of Steel-Concrete Composite Segments in Irregular Single-Tower Cable-Stayed Bridges

Kai Zhang, Xinqiang Wu, Haihui Xie, Musheng Ye, Haiyang Zhang, Genfa Chu, Xuan FeiLecture Notes in Civil Engineering 2024 · DOI · OpenAlex

Abstract

This study investigates the complex stress distribution within the steel-concrete composite segments of the Dianbu River Bridge, a hybrid beam cable-stayed bridge in Anhui Province. Using ABAQUS for spatial finite element analysis, the research clarifies the load-bearing pathways between disparate materials. Findings reveal that primary forces transition through steel plates and concrete segments via a bidirectional transfer principle, while auxiliary components like rear pressure plates serve primarily as construction aids. The analysis confirms the structural safety and rationality of the bridge's composite segment design.

Introduction: The Challenge of Hybrid Junctions

In modern bridge engineering, hybrid girders—combining lightweight steel for long main spans with heavy concrete for side spans—offer an efficient balance of structural performance. However, the interface where these materials meet, known as the steel-concrete composite segment, represents a significant structural challenge. Due to the stark differences in stiffness and material properties between steel and concrete, the stress distribution at this junction is non-linear and highly complex.

For "irregular" structures like the Dianbu River Bridge, which features a unique crescent-shaped tower and an asymmetrical layout, standard analytical formulas are often insufficient. Engineers require precise mapping of force "flow" through this junction to prevent structural failure or cracking under operational loads.

Elevation view and dimensions of the Dianbu River Bridge, showing the asymmetrical (84 + 152)m span configuration.

Methodology

The study employed Finite Element Analysis (FEA) using ABAQUS 2020 to develop a high-fidelity spatial model of the entire bridge. The modeling approach was distinguished by its granular detail:

  • Concrete Elements: Modeled as solid units (C3D8R) to capture volumetric stress.
  • Steel Components: Girders, ribs, and diaphragms were represented as shell units (S4R).
  • Reinforcement: Steel bars and stay cables were modeled as truss units (T3D2) embedded within the concrete.
  • Calibration: The model was refined using construction blueprints and on-site documentation to ensure the virtual "lattice chambers" and "shear nails" accurately reflected the physical structure.

Key Insights into Force Transmission

The research identified a specific four-step sequence for internal force transmission: internal forces move from the steel transition segments → composite steel plates → composite concrete → concrete transition segments.

A critical finding was the distinction between primary load-bearing components and auxiliary elements. The steel plates within the bonding section were identified as the primary "workhorses," experiencing compressive stresses up to 319.4 MPa—approaching the material's yield strength. In contrast, components like the head steel plates and rear pressure plates exhibited significantly lower stress levels (16–30 MPa).

Detailed cross-section of the steel-concrete composite segment showing the transition between materials and key components like the rear-supported plate and horizontal partition.

The study concludes that these low-stress components function primarily as "blocking" elements or construction requirements (e.g., for holding grout) rather than critical load-bearing paths. Furthermore, the "lattice chambers" formed by interlocked steel and concrete showed stresses under 50 MPa, indicating a high degree of structural redundancy and safety.

Conclusion and Future Directions

The simulation validates the current construction methodology of the Dianbu River Bridge, confirming its reliability under static loads. However, the authors note that this study focuses exclusively on static force transmission. Future research will address the effects of seismic loading, wind, and traffic vibrations. Additionally, investigating long-term material behaviors such as concrete creep and bond degradation remains a priority for ensuring the bridge's multi-decade structural integrity.

Summary updated

Abstract

Abstract In response to the complex stress distribution challenges in the steel-concrete composite segments of hybrid beam cable-stayed bridges, this study focuses on the steel-concrete composite segments of the Dianbu River Bridge in Anhui Province. A comprehensive spatial model of the entire bridge was established using ABAQUS for an overall static analysis. The analysis aimed to elucidate the stress distribution within the composite segments, including the concrete, steel plates, and rear compression plates, and to identify the specific load-bearing pathways within the structure. The results of the analysis indicate that the primary load-bearing pathways traverse the steel transition segments, the steel plates of the composite segments, the concrete of the composite segments, and the concrete transition segments, by bidirectional load transfer principles. The construction method of the steel-concrete composite segments of the bridge tower is deemed to be rational, ensuring structural safety and reliability.
BibTeX
@inproceedings{zhang2024study,
  author = {Kai Zhang and Xinqiang Wu and Haihui Xie and Musheng Ye and Haiyang Zhang and Genfa Chu and Xuan Fei},
  title = {{Study on the Force Transmission Mechanism of Steel-Concrete Composite Segments in Irregular Single-Tower Cable-Stayed Bridges}},
  booktitle = {Lecture Notes in Civil Engineering},
  year = {2024},
  doi = {10.1007/978-981-97-5814-2\_21},
}
Figure