Thermal Degradation and Spallation in High Temperature Interfaces

17 concepts10 papers1 proposal

In extreme thermal environments—ranging from the 400°C depths of oil recovery wells to the 1500°C infernos of gas turbines—materials do not just weaken; they fundamentally transform. The failure of protective coatings and lubricants in these settings is rarely a single event. Instead, it is a progressive loss of structural integrity driven by internal stress accumulation, chemical decomposition, and microscopic void formation.

The Mechanical Cost of Oxidation

When metals are exposed to high heat, they inevitably form a thermally grown oxide (TGO) layer. While this layer can act as a shield, its growth introduces a "silent" form of damage. As Hirohisa Kimachi et al. demonstrate in Evaluation of Thermal Damage of Thermal Barrier Coatings by Using Raman Microspectroscopy, the accumulation of compressive residual stress within this oxide layer can exceed 1.0 GPa.

This stress arises because the oxide layer and the underlying substrate expand and contract at different rates. Eventually, the internal pressure becomes so great that the coating undergoes spallation—a catastrophic peeling where the protective layer flakes off, exposing the vulnerable metal beneath. Ying Chen et al. explain in Pt effect on early stage oxidation behaviour of Pt-diffused γ-Ni/γ’-Ni3Al coatings that this can be mitigated by slowing down phase transformations. By using platinum to stabilize specific phases, researchers can reduce the lattice mismatch between layers, lowering the overall compressive stress and extending the coating's life.

Diffusion and the Kirkendall Effect

Failure also occurs at the atomic level through the movement of elements. In multi-component alloys, different atoms diffuse at different rates. As Hegang Du et al. describe in Study on the growth mechanism of the internal oxide layer in 9% Ni cryogenic steel, this differential diffusion leads to the Kirkendall effect: the formation of microscopic voids at the metal-oxide interface.

As these voids coalesce, they create a plane of weakness. When combined with the thermal expansion mismatches identified by Guangyuan Liu et al. in Axial Air-cooled Road Wheel Design, these gaps cause the protective scale to lose adhesion. In heavy machinery, this manifests as the separation of rubber-metal composites; in aerospace, it results in the total loss of thermal barrier integrity.

The Breakdown of Lubrication

Lubrication faces a parallel challenge. Traditional liquid lubricants and greases undergo physical and chemical breakdown above 200°C, as noted by Jun Cao et al. in A Review of Surface Treatments for Sliding Bearings Used at Different Temperature. This necessitates a shift to solid lubricants, but even these are not immune to heat.

Solid lubricants like $WS_2$ often fail due to oxidation in humid or high-heat environments. To solve this, Songmin Zhang et al. proposed doping these coatings with Boron in Effect of B Element Doping on High-Temperature Tribological Properties of WS2-Based Composite Coatings. The boron acts as a stabilizer, maintaining low friction even at 450°C. Similarly, Hongyuan Su et al. found that adding molybdenum particles to plasma-sprayed coatings can act as a thermal shield, preventing the lubricant from decomposing during the high-energy fabrication process itself (Role of Mo particles on microstructure and tribological properties of atmospheric plasma sprayed Mo reinforced BN-NiCr coatings).

Engineering for Resilience

Modern research focuses on two paths to overcome these degradation mechanisms:

  1. Structural Evolution: Yang Wu et al. show in Structural Evolution and Mechanical Behavior of Ytterbia Doped Hafnia Biphasic Ceramics under Annealing at 1500 °C that creating "sandwich" structures in ceramics can enhance fracture toughness, allowing materials to absorb the energy of phase transitions rather than cracking.
  2. Computational Discovery: To find alloys that can survive near 1150°C without spalling, Shanshan Hu et al. utilized machine learning to move beyond simple mixtures, identifying complex high-entropy alloys (HEAs) with superior oxidation resistance (Machine learning and high-throughput computational guided development of high temperature oxidation-resisting Ni-Co-Cr-Al-Fe based high-entropy alloys).

Ultimately, surviving extreme heat requires more than just high melting points; it requires managing the microscopic stresses and chemical shifts that occur at the interfaces where materials meet their environment.

Key Foundational Work

Evaluation of Thermal Damage of Thermal Barrier Coatings by Using Raman Microspectroscopy (2010) — contributed 3 concept elements to this direction.
Study on Clearance Optimization of All-metal Screw Pumps: Experiment and Simulation (2017) — contributed 1 concept elements to this direction.
History & citationVersion 1 · 2026-10-04

Current · Permanent link

View frozen version 1

Cite this direction

Latest version (a living page):

@misc{lacuna_thermal_lubricant_degradation_aff8df0a,
  title = {thermal lubricant degradation},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/thermal-lubricant-degradation/rdr_aff8df0a3402402fa8059ef7bdf5378b},
  note = {Latest version of a living research direction; cite a version for a fixed text. Accessed 2026-11-20},
}

This exact version (version 1, frozen text):

@misc{lacuna_thermal_lubricant_degradation_aff8df0a_v1,
  title = {thermal lubricant degradation},
  author = {{Lacuna}},
  howpublished = {Lacuna research direction},
  year = {2026},
  url = {https://lacuna.tiptreesystems.com/direction/thermal-lubricant-degradation/rdr_aff8df0a3402402fa8059ef7bdf5378b/v/1},
  note = {Version 1, frozen 2026-10-04. Accessed 2026-11-20},
}
About

These directions overlap with this one through shared papers.

See something wrong? Report a mistake