Structural Evolution and Mechanical Behavior of Ytterbia Doped Hafnia Biphasic Ceramics under Annealing at 1500 °C

Yang Wu, Hao Lan, Xiaoming Sun, Zihao Hu, Yonghui Sun, Huifeng Zhang, Chuanbing Huang, Weigang ZhangCrystals 2024 · DOI

TL;DR

This paper investigates Ytterbia-doped Hafnia (YbSH) ceramics, a promising material for high-temperature thermal barrier coatings (TBCs). By annealing these ceramics at 1500°C, researchers observed the formation of a unique C/M/C (cubic/monoclinic/cubic) sandwich structure. This structural evolution significantly enhances fracture toughness, making YbSH a more robust candidate for extreme environments.

What Problem Does This Paper Address?

Traditional thermal barrier coatings, like Yttria-Stabilized Zirconia (YSZ), perform well up to 1200°C. However, exceeding this temperature leads to phase transitions, volume expansion, and residual stress, ultimately causing coating failure. Hafnia (HfO2) is a potential alternative due to its higher phase transition temperature, but it suffers from inherently low fracture toughness, limiting its widespread application. This research aims to address this limitation by exploring structural modifications in HfO2-based ceramics to improve their mechanical performance at ultra-high temperatures.

Methods

The researchers synthesized YbSH nanopowders using a hydrothermal method. These powders were then cold-pressed and sintered to form dense ceramic bulks. The core of the study involved annealing these ceramics at 1500°C for varying durations (3h to 48h).

Key characterization techniques included:

  • X-ray Diffraction (XRD): To analyze phase compositions (cubic and monoclinic phases) and their evolution with annealing time. Rietveld refinement was used for quantitative phase analysis.
  • Scanning Electron Microscopy (SEM): To observe the microstructure and grain morphology.
  • Energy Dispersive Spectrometry (EDS): To determine elemental distribution, particularly Ytterbium.
  • Microhardness Testing: To measure the Vickers hardness of the ceramics.
  • Indentation Method: Used to calculate fracture toughness (KIC) and fracture energy.
  • Ultrasonic Method: To determine the elastic modulus.

Datasets

Not discussed in the paper. The study relies on experimental synthesis and characterization of the YbSH ceramic material.

Key Insights and Ideas

  • Emergence of a C/M/C Sandwich Structure: The annealing process at 1500°C is crucial for forming a distinct "sandwich" structure where cubic phases encapsulate monoclinic phases. This is not a simple mixture but a layered arrangement.
  • Monoclinic Phase as a Toughening Agent: While cubic HfO2 is brittle, the monoclinic phase, when integrated into this sandwich structure, appears to be the key to enhanced toughness. The study shows a direct correlation between the increase in monoclinic phase content and improved fracture toughness.
  • Role of Residual Stress: The difference in thermal expansion coefficients and the presence of residual compressive stress within the monoclinic phase are identified as critical factors. These stresses help bridge and deflect cracks, preventing catastrophic failure.
  • Diffusive vs. Martensitic Phase Transition: Unlike the problematic martensitic transformation in YSZ above 1200°C, the C to M phase transition in YbSH is described as diffusive. This is important because it avoids the large volume changes that lead to coating delamination.
  • Yb³+ Diffusion as a Driving Force: The distribution of Ytterbium plays a significant role. Yb³+ ions tend to migrate, influencing the nucleation and growth of the monoclinic phase at grain boundaries.

Key Results

  • Fracture Toughness Enhancement: The fracture toughness of the YbSH ceramics increased significantly with annealing time. It rose from 2.18 MPa·m⁰.⁵ in the unannealed state to a remarkable 2.83 MPa·m⁰.⁵ after 48 hours of annealing. This represents a ~30% improvement.
  • Increased Fracture Energy: Correspondingly, fracture energy also saw a substantial increase, from 27.48 N·m⁻¹ to 45.12 N·m⁻¹ after annealing, a ~64% jump.
  • Monoclinic Phase Growth: The weight fraction of the monoclinic (M) phase increased from 41.8% in the unannealed state to 49.8% after 48 hours of annealing.
  • Hardness Decrease: While toughness improved, the Vickers hardness showed a gradual decrease with annealing time, from 732.9 Hv initially to 583 Hv after 48 hours. This trade-off between hardness and toughness is common in materials science.
  • Comparison to Other TBC Materials: The achieved fracture toughness (2.83 MPa·m⁰.⁵) is noted as being higher than many other potential TBC materials, highlighting the promise of this YbSH system.

Limitations and Future Work

  • Hardness vs. Toughness Trade-off: The study observed a decrease in hardness with increased annealing time. Future work could explore strategies to optimize both properties simultaneously.
  • Long-Term Stability: While annealing at 1500°C for 48 hours showed positive results, the long-term performance and microstructural stability of these C/M/C sandwich structures under prolonged operational conditions (e.g., thermal cycling) would require further investigation.
  • Optimization of Yb Doping: The study used 10 mol% Yb³+. Investigating different doping concentrations could potentially further refine the microstructure and mechanical properties.
  • Application-Specific Testing: While promising for TBCs, direct testing of these YbSH ceramics in simulated engine environments would be the next logical step to validate their performance.

Summary updated

Abstract

HfO2 has become a promising thermal barrier coating material due to its similarity in structure and chemical properties with ZrO2 and its higher phase structure transition temperature. However, the fracture toughness of HfO2 is not ideal, greatly limiting its application. In this report, we find a special sandwich structure of ceramics, comprising a cubic (C) phase /monoclinic (M) phase/cubic (C) phase. The microstructural evolution and mechanical properties of these ceramics were investigated under annealing at 1500 °C. The results indicate that, with an increase in annealing duration, there was a gradual augmentation in the proportion of the monoclinic (M) phase and the fracture toughness increased from 2.18 MPa·m0.5 to 2.83 MPa·m0.5 after 48 h of annealing, which is higher than many potential TBC materials. The residual compressive stress present in the M phases during the progression of crack propagation served to facilitate the bridging and deflection of cracks. As such, this process led to the alleviation of stress concentration at the crack tip, ultimately enhancing the toughening effect.
BibTeX
@inproceedings{wu2024structural,
  author = {Yang Wu and Hao Lan and Xiaoming Sun and Zihao Hu and Yonghui Sun and Huifeng Zhang and Chuanbing Huang and Weigang Zhang},
  title = {{Structural Evolution and Mechanical Behavior of Ytterbia Doped Hafnia Biphasic Ceramics under Annealing at 1500 °C}},
  booktitle = {Crystals},
  year = {2024},
  doi = {10.3390/cryst14030279},
}
Figure