Uplink Achievable Rate Maximization for Reconfigurable Intelligent Surface Aided Millimeter Wave Systems With Resolution-Adaptive ADCs

Yue Xiu, Jun Zhao, Ertugrul Basar, Marco Di Renzo, Wei Sun, Guan Gui, Ning Wei

This paper, published in late 2020, addresses a critical bottleneck in the deployment of 5G and 6G millimeter-wave (mmWave) systems: the massive power consumption and high cost of base station hardware.

TL;DR

The researchers propose a joint optimization framework that combines Reconfigurable Intelligent Surfaces (RIS) with resolution-adaptive analog-to-digital converters (RADCs). Their findings demonstrate that an RIS can effectively "compensate" for the signal degradation caused by low-resolution hardware, allowing base stations to maintain high data rates while significantly reducing power consumption.

What Problem Does This Paper Address?

While mmWave frequencies offer massive bandwidth, they are notoriously fragile, easily blocked by buildings or even foliage. To combat this, engineers use massive antenna arrays to create "beams" of signal. However, every antenna typically needs to be backed by an Analog-to-Digital Converter (ADC).

The problem is that high-resolution ADCs (e.g., 8-12 bits) are power-hungry—their power consumption scales exponentially with the number of bits. In a massive MIMO setup, this becomes a thermal and financial nightmare. Researchers have looked at using low-resolution ADCs to save power, but this introduces "quantization noise" that kills the data rate. This paper asks: Can we use an RIS (a smart mirror for radio waves) to clean up the signal enough that we can get away with using cheap, low-power, adaptive ADCs?

Methods

The authors model a multi-user uplink system where an Access Point (AP) uses a limited number of RF chains and resolution-adaptive ADCs. They aim to maximize the achievable sum rate by jointly optimizing four variables:

  1. ADC Quantization Bits ($b$): Dynamically choosing how many bits to use for each RF chain.
  2. Beam Selection Matrix ($W$): Deciding which signals from the antenna array to process.
  3. RIS Phase Shifts ($\Theta$): Tuning the "smart mirror" to reflect signals toward the AP.
  4. Decoding Vectors ($u$): The digital processing used to separate user signals.

Because these variables are "coupled" (changing one affects the optimal value of the others), the problem is non-convex and mathematically "hard" (NP-hard). To solve it, they proposed a Block Coordinated Descent (BCD) algorithm. This approach breaks the big problem into smaller pieces:

  • Successive Convex Approximation (SCA): Used to handle the tricky discrete bit-allocation and beam selection.
  • Majorize-Minimization (MM): Used to optimize the decoding vectors.
  • Manifold Optimization (MO): Used to solve for the RIS phase shifts, ensuring they stay within the physical limits of the hardware.

Datasets

The paper relies on numerical simulations rather than a physical dataset. They use a standard geometric mmWave channel model that accounts for:

  • Large-scale fading (path loss).
  • Small-scale fading (multipath effects).
  • Log-normal shadowing (interference from obstacles).
  • Specific parameters: 10 users, 64 AP antennas, 8 RF chains, and an RIS with varying elements (8 to 32).

Key Insights and Ideas

  • The RIS as a "Hardware Loss Mitigator": The most significant insight is that the RIS doesn't just boost signal strength; it acts as a buffer against hardware imperfections. By optimizing the RIS, you can achieve the same performance with 3-bit ADCs that you would normally get with much higher resolution.
  • Adaptive vs. Fixed Resolution: The paper shows that adapting the bit-depth of ADCs based on the channel state is far superior to using a fixed low-resolution (e.g., 1-bit) setup.
  • Interference Management: In multi-user scenarios, the RIS helps "null out" interference between users, which is particularly helpful when the ADC resolution is low and the signal is already "noisy."

Key Results

  • Superiority over SOTA: The proposed BCD algorithm consistently outperformed state-of-the-art methods (like SHC-MO and MMSQE-BA-MO) in terms of achievable sum rate.
  • The 8-bit Benchmark: A key simulation showed that an RIS-aided system with adaptive low-res ADCs could achieve the same sum rate as a standard system (no RIS) using high-resolution 8-bit ADCs.
  • Rapid Convergence: Despite the complexity of the joint optimization, the BCD algorithm typically converges within about 10 iterations, making it computationally feasible.
  • Scaling: The sum rate increases significantly as the number of RIS reflecting elements ($N_r$) increases, proving that adding more "passive" elements to the environment is a viable alternative to adding "active" power-hungry components to the base station.

Limitations and Future Work

  • Perfect CSI Assumption: The study assumes the system has "Perfect Channel State Information" (CSI). In reality, estimating the channel for an RIS is very difficult because the RIS elements are passive and cannot transmit pilot signals themselves.
  • Static Environment: The model assumes a static snapshot. Future work would need to address how the BCD algorithm handles high-mobility users (e.g., cars) where the channel changes every few milliseconds.
  • Wideband vs. Narrowband: This paper focuses on a narrowband model. Extending this to wideband (OFDM) systems, which are standard in 5G, would add another layer of complexity to the beam selection and bit allocation.

Summary updated

Abstract

In this letter, we investigate the uplink of a reconfigurable intelligent surface (RIS)-aided millimeter-wave (mmWave) multi-user system. In the considered system, however, problems with hardware cost and power consumption arise when massive antenna arrays coupled with power-demanding analog-to-digital converters (ADCs) are employed. To account for practical hardware complexity, we consider that the access point (AP) is equipped with resolution-adaptive analog-to-digital converters (RADCs). We maximize the achievable rate under hardware constraints by jointly optimizing the ADC quantization bits, the RIS phase shifts, and the beam selection matrix. The formulated problem is non-convex. To efficiently tackle this problem, a block coordinated descent (BCD)-based algorithm is proposed. Simulations demonstrate that an RIS can mitigate the hardware loss due to the use of RADCs, and that the proposed BCD-based algorithm outperforms state-of-the-art algorithms.
BibTeX
@article{xiu2021uplink,
  author = {Yue Xiu and Jun Zhao and Ertugrul Basar and Marco Di Renzo and Wei Sun and Guan Gui and Ning Wei},
  title = {{Uplink Achievable Rate Maximization for Reconfigurable Intelligent Surface Aided Millimeter Wave Systems With Resolution-Adaptive ADCs}},
  journal = {IEEE Wireless Communications Letters},
  year = {2021},
  url = {https://openreview.net/forum?id=jIkVO5T6KE},
}

Loading related content...

Figure