Unmanned Leg-Wheel Vehicle Design and of Vertical Step Passability Performance Analysis

Ruotian Wang, Huaying Li, Yunhai Wang, Zhixiong Wang2016 · DOI

Abstract

In order to achieve high mobility for country crossing and the ability of climbing vertical obstacles, a new locomotion mechanism that combines legs and wheels is proposed, and a prototype mobile robot that adopts the mechanism is introduced, actions for obstacle climbing is designed. Focused on forces and power requirements on leg-wheel mechanism in the process of obstacle climbing, calculated the maximum of output torque during motor drive legs rotation, established a model of unmanned ground vehicle through the multibody dynamics modeling software ADAMS, simulated and analyzed the process of obstacle climbing. Result show that the proposed structure meet the demand of 220mm high platform climbing with the maximum rotating torque 4.99N·m.

Introduction

Unmanned Ground Vehicles (UGVs) in urban environments face a classic trade-off: wheels are fast and energy-efficient on flat ground but fail at vertical obstacles like curbs, while legs offer superior traversability but are mechanically complex and slow. This paper introduces a hybrid leg-wheel robot designed to bridge this gap, specifically focusing on vertical step passability. For a small robot to be effective in reconnaissance or search-and-rescue, it must scale ledges taller than its own chassis without the computational overhead of a traditional quadruped.

Mechanical Design and Climbing Strategy

The proposed robot features four legs capable of full 360-degree rotation, each ending in a wheel powered by an internal hub motor. A key structural feature is the "inner-spring damping suspension," which allows for ±15° of swing to absorb shocks during movement.

To navigate vertical obstacles, the researchers developed a specific six-step "rotate and follow" sequence. The robot first "stands up" to raise its center of gravity, reaches a front leg onto the platform, and then utilizes the 360° rotation of the legs to "pull" the rest of the chassis upward.

The six-step "rotate and follow" sequence for climbing a vertical obstacle.

Modeling and Simulation

The team validated the design through a combination of theoretical torque balance equations and multibody dynamics simulation using ADAMS (Automated Dynamic Analysis of Mechanical Systems). This allowed for a high-fidelity physics analysis of the forces and torques required during the climbing process.

Geometric model used for calculating torque requirements during the climbing process.

A critical insight from the geometric modeling was the identification of the maximum torque demand. The researchers found that the highest load on the motors occurs when the leg is nearly horizontal (specifically at a -18.8° angle), which is the point of maximum mechanical disadvantage. The simulation showed a maximum rotating torque of 4.99 N·m, which closely matched the theoretical prediction of 4.93 N·m (a 2.3% discrepancy attributed to realistic contact constraints in the simulation).

Key Results and Performance

  • Vertical Passability: The robot successfully climbed a 220mm vertical platform, exceeding the initial design requirement of 200mm.
  • Torque Specifications: The determination of the 4.99 N·m maximum torque provides a concrete specification for motor selection in similar hybrid vehicles.
  • Compact Efficiency: The robot achieved these results within a compact footprint of 500mm x 500mm x 150mm and a weight under 20kg.

Limitations and Future Work

While the simulation results are robust, the authors noted that the theoretical model assumes mass is perfectly concentrated at the centroid. Real-world mass distribution may affect stability during the "rotate and reach" phase. Additionally, future testing is required to evaluate performance on low-friction surfaces (like wet marble or gravel) where the leg's "pulling" action might lead to slipping. Physical prototype testing will be essential to account for sensor noise and structural flex under load.

Summary updated

Abstract

In order to achieve high mobility for country crossing and the ability of climbing vertical obsta- cles, a new locomotion mechanism that combines legs and wheels is proposed, and a prototype mobile robot that adopts the mechanism is introduced, actions for obstacle climbing is designed. Focused on forces and power requirements on leg-wheel mechanism in the process of obstacle climbing, calculated the maximum of output torque during motor drive legs rotation, established a model of unmanned ground vehicle through the multibody dynamics modeling software ADAMS, simulated and analyzed the process of obstacle climbing. Result show that the proposed structure meet the demand of 220mm high platform climbing with the maximum rotating torque 4.99N·m. KEYWORD: unmanned ground vehicle, obstacle climbing, leg-wheel structure.
BibTeX
@misc{wang2016unmanned,
  author = {Ruotian Wang and Huaying Li and Yunhai Wang and Zhixiong Wang},
  title = {{Unmanned Leg-Wheel Vehicle Design and of Vertical Step Passability Performance Analysis}},
  year = {2016},
  doi = {10.2991/mmme-16.2016.9},
}
Figure