OmniQuad: a Wheeled-Legged Hybrid Robot with Omnidirectional Wheels

Francesco Iotti, Alok Ranjan, Franco Angelini, Manolo GarabiniarXiv 2026 · DOI · arXiv

TL;DR

OmniQuad is a hybrid robot that merges the agility of a quadruped with the efficiency of mecanum wheels, enabling high-speed omnidirectional movement on flat ground and the ability to climb over or crouch under obstacles. By integrating mecanum wheels directly into the feet, the researchers have created a platform that can move laterally without turning, significantly improving maneuverability in confined spaces.

What Problem Does This Paper Address?

Roboticists often face a "locomotion trade-off." Legged robots are masters of uneven terrain and stairs, but they are relatively slow and energy-inefficient on flat surfaces. Wheeled robots are fast and efficient but are easily defeated by a single step or a high curb.

While hybrid "wheeled-legged" robots exist, most use standard wheels that require complex steering mechanisms or leg-based maneuvers to change direction. The authors of this paper tackle the challenge of creating a robot that maintains high-speed efficiency and obstacle-clearing capabilities while adding holonomic (omnidirectional) mobility—the ability to move in any direction (forward, backward, or sideways) without changing its orientation.

Figure 1: OmniQuad hybrid robot.

Methods

The researchers developed a custom wheeled-foot assembly that serves as the robot's end-effector. Each of the four legs features three degrees of freedom (DOF): two for the leg joints (hip and knee) and one for the wheel.

Key technical components include:

  • Mechanical Design: A custom assembly housing a mecanum wheel, a high-torque AASUN planetary gearbox (15:1 ratio), and a T-motor brushless motor.
  • Actuation: The legs use "EM-Act" modular actuators, while the wheels are driven by compact brushless motors controlled via Moteus r.411 drivers.
  • Control Architecture: The system runs on a Raspberry Pi 4 with a Pi3Hat for low-level motor communication. The team developed a dual-mode control scheme: a kinematic model for wheeled omnidirectional movement and an inverse kinematics model for legged maneuvers.
  • Obstacle Detection: Instead of expensive vision sensors, the robot uses torque feedback from the wheel motors. When a wheel hits an obstacle and the torque spikes, the "Obstacle Climbing Module" automatically triggers a leg-lifting sequence.
Figure 2: Components in the actuation system of the wheeled-foot: (a) mecanum wheel; (b) T-motor antigravity 4004; (c) Moteus r.411 ; (d) AASUN AM-28P gearbox.

Datasets

Not discussed in the paper. As a hardware and control systems paper, the evaluation relied on real-world experimental trials rather than standardized datasets.

Key Insights and Ideas

  • The Leg as Suspension: In hybrid mode, the robot’s legs aren't just for climbing; they act as an active suspension system. This helps maintain constant contact between the mecanum wheels and the ground, which is critical because mecanum wheels rely on specific contact angles to achieve omnidirectional motion.
  • Lateral Efficiency: By using mecanum wheels, OmniQuad can perform lateral (sideways) movements more efficiently than traditional quadrupedal "sidestepping" gaits, which involve complex leg coordination and higher energy costs.
  • Torque-Based Intelligence: The ability to detect and clear obstacles using only motor current/torque data demonstrates a robust, low-cost way to handle "blind" navigation in cluttered environments.
  • Height Adaptability: The robot can dynamically adjust its base height. This allows it to "crouch" to pass under low-clearance barriers that would stop a standard wheeled platform.

Key Results

The OmniQuad was put through a gauntlet of indoor and outdoor tests:

  • Speed: It achieved a maximum forward velocity of 2.0 m/s and a lateral velocity of 1.5 m/s on flat ground.
  • Obstacle Traversal: The robot successfully climbed a 100 mm step (roughly 1.25x its wheel radius) using its legged locomotion mode.
  • Low Clearance: It demonstrated the ability to lower its base to 180 mm to pass under a low-hanging rod.
  • Payload: During legged locomotion, it successfully carried an additional 2.5 kg payload (roughly 35% of its own 7 kg mass) while clearing a step.
  • Battery Life: The estimated battery life is approximately 1.5 hours in hybrid mode, though this varies significantly depending on how much the energy-intensive leg motors are used compared to the efficient wheel motors.

Limitations and Future Work

The authors identified several areas for improvement:

  • Vibrations: Mecanum wheels inherently generate vibrations due to the rollers' discontinuity, which can affect sensor readings and traction on certain surfaces like grass.
  • Degrees of Freedom: The current 2-DOF leg design lacks a "hip abduction" joint (sideways leg swing), which limits stability during certain climbing maneuvers. The team plans to add this in future iterations.
  • Autonomy: Currently, the robot relies on encoder-based odometry and IMU data. Future work will integrate LiDAR and depth cameras to allow for fully autonomous navigation in unknown, dynamic environments.
  • Thermal Limits: During heavy payload tests (3 kg), the motor drivers overheated, indicating a need for better thermal management or more powerful actuators for heavy-duty tasks.

Summary updated

Abstract

Combining wheeled and legged locomotion within a single robotic platform offers the potential to harness the advantages of both systems. The development of such hybrid systems remains an active area of research. While legged robots exhibit remarkable adaptability for traversing uneven and rugged terrains, their relatively low speed limits their practicality in indoor environments. Conversely, wheeled robots demonstrate higher efficiency on flat surfaces but often encounter difficulties when navigating obstacles such as steps. This paper introduces OmniQuad, a novel hybrid robot that integrates mecanum wheels with legged locomotion to exploit the benefits of both modalities. Mecanum wheels provide omnidirectional mobility, enhancing the robot's manoeuvrability by enabling agile movement in confined spaces and the ability to maintain a consistent orientation during task execution. In this work, we first present the design of a custom wheeled-foot featuring mecanum wheels. Subsequently, we describe the complete robot assembly, comprising these wheeled feet and EM-Act actuators. Finally, we detail the control scheme developed to govern the OmniQuad and evaluate its performance through experimental trials conducted in both indoor and outdoor environments.
BibTeX
@misc{iotti2026omniquad,
  author = {Francesco Iotti and Alok Ranjan and Franco Angelini and Manolo Garabini},
  title = {{OmniQuad: a Wheeled-Legged Hybrid Robot with Omnidirectional Wheels}},
  year = {2026},
  eprint = {2610.38502},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2610.38502},
}
Figure