Abstract
Fractures are ubiquitous and lead to catastrophic failure of materials. While fracture in a two-dimensional plane is well understood, all fractures are, in fact, extended and propagate in a three-dimensional space and their behavior is more complex. Here we show that forward propagation of a fracture front always occurs through an initial rupture, nucleated at some localized position, followed by very rapid transverse expansion at velocities as high as the Rayleigh-wave speed. We study a circular geometry to achieve an uninterrupted extended fracture front and use fluid to control the loading conditions that determine the amplitude of the forward jump; we find this amplitude correlates with the transverse velocity. Dynamic rupture simulations capture the observations for only high transverse velocity. These results highlight the importance of transverse dynamics in the forward propagation of extended fracture.
Introduction
In classical fracture mechanics, cracks are often simplified as two-dimensional lines where the tip is a single point. However, real-world fractures are three-dimensional entities with extended fronts. While 2D models provide a solid foundation, they fail to explain the irregular patterns and "lances" often observed on fracture surfaces. Understanding how these extended fronts propagate is crucial for predicting material failure in everything from industrial components to geological faults.
Recent research has revealed that these fronts do not advance in a smooth, uniform manner. Instead, they exhibit a "stick-break" instability, where the front remains stationary for a period before jumping forward. This study investigates the underlying dynamics of these jumps, specifically focusing on the transverse expansion that occurs during each forward movement.
Experimental Methodology
To observe these dynamics in detail, researchers utilized a "benchtop geology" approach combined with high-speed imaging. The experimental setup involved 3D-printed optically clear PMMA (acrylic) cylinders, each containing a pre-existing "penny-shaped" internal crack.
Fracture was driven by injecting fluid (water-glycerol mixtures) into the center of the crack. By varying the fluid's viscosity (from 1 cP to 800 cP), the researchers could control the "lag" between the pressurized fluid front and the actual crack tip, thereby tuning the stress conditions at the front. The propagation was captured using high-speed imaging at 100,000 frames per second, with fluorescein dye and blue LED lighting used to distinguish the fluid from the dry fracture tip.
The Stick-Break Instability and Transverse Zipping
The experiments revealed that the fracture front advances through discrete jumps. The front "sticks" for up to a millisecond, accumulating stress, and then "breaks" forward suddenly. Crucially, this "break" is not a simultaneous forward leap across the entire front. Instead, it begins at a localized nucleation point and then "zips" sideways (transversely) around the circumference of the crack.
This transverse expansion occurs at astonishing speeds—up to 900 m/s in PMMA. This velocity is nearly identical to the Rayleigh-wave speed ($C_R \approx 940$ m/s), the theoretical physical speed limit for crack propagation in the material. While the instantaneous transverse velocity is extremely high, the time-averaged radial velocity of the crack is much slower (approximately 3 m/s) due to the relatively long duration of the "stick" phases.
Results and Discussion
The study found a strong correlation between the amplitude of the forward jump ($\delta\lambda$) and the transverse velocity. For jumps larger than 2 mm, the transverse velocity consistently approached the Rayleigh-wave speed. Higher fluid viscosity increased the lag between the fluid and the crack tip, leading to larger forward jumps and more distinct, high-velocity transverse events.
Numerical modeling using a spectral boundary integral method (the Uguca software) was employed to simulate the 3D elastodynamic equations. These simulations successfully reproduced the experimental crack profiles and high transverse velocities, confirming that this "zipping" effect is a fundamental characteristic of 3D fracture dynamics.
However, a discrepancy was noted for very small jumps (under 200 µm), where standard brittle fracture frameworks failed to accurately predict transverse velocities. This suggests that when the jump size is comparable to the "cohesive zone"—the region where the material is actively tearing—more complex models incorporating fluid-structure interaction or cohesive zone dynamics are required.
Conclusion
This research highlights the critical role of transverse dynamics in the propagation of extended fracture fronts. The discovery of the "stick-break" instability and the near-Rayleigh-wave speed "zipping" provides a new perspective on how fractures evolve in three dimensions. These findings have significant implications for understanding material failure and could offer new insights into geophysical phenomena, such as how microearthquakes distribute stress along fault lines. Future work will need to address the complexities of material heterogeneity and the coupling of fluid dynamics with rapid fracture events.
Summary updated