Abstract
Fractures are ubiquitous and can lead to the catastrophic material failure of materials. Although fracturing in a two-dimensional plane is well understood, all fractures are extended in and propagate through three-dimensional space. Moreover, their behaviour is complex. Here we show that the forward propagation of a fracture front occurs through an initial rupture, nucleated at some localized position, followed by a very rapid transverse expansion at velocities as high as the Rayleigh-wave speed. We study fracturing in a circular geometry that achieves an uninterrupted extended fracture front and use a fluid to control the loading conditions that determine the amplitude of the forward jump. We find that this amplitude correlates with the transverse velocity. Dynamic rupture simulations capture the observations for only a high transverse velocity. These results highlight the importance of transverse dynamics in the forward propagation of an extended fracture.
Introduction
Fractures are a primary cause of material failure, yet their three-dimensional propagation remains complex and often misunderstood. While traditional 2D models treat cracks as lines advancing uniformly, real-world fractures involve surfaces terminating at extended "crack fronts." This study reveals that these fronts do not advance smoothly. Instead, they propagate through a "stick-break" mechanism: a localized point on the front ruptures first (nucleation), followed by an extremely rapid transverse expansion across the entire front at speeds approaching the Rayleigh-wave limit—the speed of sound on a material's surface.
Experimental Methodology
To isolate these 3D dynamics, researchers utilized 3D-printed, optically clear PMMA (acrylic) cylinders containing an internal "penny-shaped" crack. This circular geometry provides an uninterrupted front, free from edge interference that might otherwise obscure the intrinsic dynamics of the crack tip.
Loading was controlled by injecting water-glycerol mixtures of varying viscosities ($\mu$) into the crack center. This allowed precise control over the "lag" ($\lambda$)—the distance between the pressurized fluid front and the actual crack tip. High-speed cameras filming at 100,000 frames per second and fluorescent dye were used to visualize the motion in real-time, which was then compared to 3D dynamic rupture simulations using a spectral boundary integral method.
Dynamics of Fracture Propagation
The study identifies a distinct "stick-break" instability. The crack front remains stationary ("sticks") as pressure builds, then suddenly "breaks" in a discrete forward jump. Crucially, this break is not simultaneous across the entire front. It nucleates at a single, localized spot, creating a sharp distortion that "zips" sideways (transversely) around the perimeter.
The transverse expansion velocity ($V_T$) is remarkably high, reaching up to 900 m/s—nearly the Rayleigh-wave speed ($C_R \approx 940$ m/s) of the PMMA. In contrast, the average radial velocity is much slower (~3 m/s), though instantaneous velocities during the "break" events exceed 500 m/s. The kymographs in the figure above clearly illustrate these discrete jumps ($\delta\lambda$) and the resulting space-time evolution of the front.
Key Findings and Implications
The amplitude of the forward jump ($\delta\lambda$) correlates directly with the transverse velocity. Larger jumps, driven by higher fluid viscosity and lag, result in transverse speeds hitting the Rayleigh-wave limit. However, the standard brittle fracture model begins to fail when jump sizes drop below 200 $\mu$m, suggesting that the physics changes as the jump size approaches the material's internal cohesive zone—the tiny region at the tip where the material is actually tearing.
These findings have broad implications. In seismology, they suggest that earthquake ruptures might propagate as a series of localized transverse expansions rather than uniform fault sliding. In materials science, this model provides a new framework for understanding failure in crystalline structures, where propagation might occur through the motion of atomic-level kinks.
Conclusion
By highlighting the critical role of transverse dynamics, this research shifts the paradigm of fracture mechanics from a 1D line-advance model to a 2D front-evolution model. Understanding the high-speed "zipping" of crack fronts is essential for accurately modeling and preventing material failure across scales, from consumer electronics to geological fault lines.
Summary updated