The Structural Behavior of Serrated Cast-In Anchor Channels - A Numerical Study on the Longitudinal Loading Close to the Edge

Georg Karl Kocur, Eleni Chatzi, Frank Häusler2016 · DOI

Abstract

The structural behavior of concrete members equipped with cast-in anchor channels subjected to shear loading along the longitudinal axis presents a complex modeling challenge. Current calculation methods for anchor channels have rarely been validated through physical experimentation for this specific loading condition. This study investigates the structural behavior of serrated anchor channels installed near a concrete edge and positioned orthogonally to it. Through a combination of preliminary physical test series and high-fidelity finite element (FE) simulations, the research examines crack formation and load redistribution between anchors. The findings reveal significant discrepancies between observed behavior and the predictions of current international design guidelines, particularly regarding how load is shared between front and rear anchors following initial concrete cracking.

Introduction

Anchor channels are essential components in modern construction, providing adjustable and reliable connections for structural and non-structural elements such as elevator rails and curtain wall façades. These C-shaped steel profiles are cast directly into concrete, typically featuring two or more anchors to transfer loads into the base material. While their performance under tension and transverse shear is well-documented, their behavior under longitudinal shear loading—where the load is applied parallel to the channel axis—remains a subject of ongoing research, especially when installed close to a concrete edge.

Components of a serrated cast-in anchor channel assembly.

Current engineering practice relies on design codes such as CEN/TS 1992-4 and AC232. However, these standards were largely adapted from research on simple headed fasteners and may not accurately capture the complex mechanics of multi-anchor channel systems. This study aims to bridge this knowledge gap by analyzing the interaction between ductile steel components and brittle concrete under longitudinal shear.

Methodology

The researchers adopted a hybrid experimental-numerical approach to capture the full spectrum of structural behavior.

Physical Testing and Calibration

Preliminary experiments were conducted on serrated anchor channels embedded in concrete slabs. These tests provided critical load-deflection data used to calibrate the numerical models. Special attention was paid to the "ground truth" behavior of the structural steel members and the composite assembly under increasing loads until failure.

Numerical Modeling (FEM)

Advanced Finite Element Method (FEM) simulations were performed using the ABAQUS/Standard and Explicit solvers. The modeling strategy focused on three key areas:

  1. Concrete Damage Plasticity (CDP): This model was employed to simulate the non-linear behavior of concrete, accounting for both tensile cracking and compressive crushing.
  2. Steel Plasticity: Structural steel components were modeled with non-linear plastic properties to capture phenomena such as "necking" in the anchors.
  3. Interaction and Friction: The contact between steel and concrete was modeled using Coulomb friction laws. A critical aspect was the interaction between the serrated T-bolt and the channel lips, which significantly influences load transfer.
Numerical simulation setup for longitudinal loading ($V_{ua,x}$) close to the concrete edge.

The simulations utilized the "Brutus" high-performance computing cluster at ETH Zurich to manage the high computational demand of the complex mesh geometries and non-linear interactions.

Key Insights and Results

The study yielded several critical insights that challenge existing design assumptions:

Load Redistribution Mechanisms

A primary finding was the dynamic nature of load distribution. As longitudinal shear is applied, the "front" anchor (closest to the applied load) initially bears the brunt of the force. However, once a crack forms in the concrete near this anchor, the load is redistributed to the "rear" anchors. This redistribution is a critical phase in the failure sequence that is often oversimplified in static design formulas.

Discrepancies with Design Codes

The results highlighted significant contradictions between experimental/numerical data and international standards. For instance, in a three-anchor test case, the FEM model calculated a total shear capacity of 157.1 kN, whereas the CEN/TS code predicted a lower value of 136.0 kN. This suggests that current codes may be overly conservative in some aspects while failing to capture the actual mechanical behavior of the system after initial cracking.

Failure Modes

Visualizations from the FE models confirmed that the dominant failure mode is "concrete edge failure," characterized by the formation of a fracture cone that pushes out from the concrete face. The numerical models successfully replicated this complex geometry, providing a more granular view of stress concentrations than possible through physical testing alone.

Conclusion and Future Work

This research demonstrates that the structural behavior of anchor channels under longitudinal shear is a complex process of crack-induced load redistribution. The observed discrepancies with current design guidelines suggest a need for more unified and mechanically accurate calculation methods. Future research is needed to investigate channels installed parallel to the edge and the "corner effect" where two edges influence the fracture cone development.

Summary updated

Abstract

The structural behavior of concrete members due to cast-in anchor channels subjected to shear loading in longitudinal channel axis poses a non-trivial modeling task. The explicit applicability of recent calculation methods on anchor channels has rarely been validated by physical experiments. Preliminary test series on serrated anchor channels were carried out to determine the structural behavior under longitudinal shear loading. Anchor channels were installed in concrete close to the specimen's edge and positioned orthogonal to the edge. Each anchor channel was equipped with two riveted anchors. Loading was applied over serrated bolts until failure. Special attention was paid to the crack formation during loading. Of particular interest was the point in time when the load was redistributed from the front to the rear anchor. To attain a deeper insight with respect to the failure mechanisms, finite element simulations were performed. The main challenge, additionally to the complex mesh geometry, was in modeling the physical behavior of structural steel and concrete as a composite structure. The interaction between the brittle concrete and the ductile structural steel needs to be appropriately accounted for by means of adequate numerical simulation. Numerical calibration experiments, involving the structural steel members, were performed until satisfactory convergence was achieved. Load-deflection curves obtained from physical experiments were adopted for calibration of the numerical model. The obtained hybrid numerical/experimental results appear to contradict the results calculated by means of currently available design guidelines.
BibTeX
@misc{kocur2016structural,
  author = {Georg Karl Kocur and Eleni Chatzi and Frank Häusler},
  title = {{The Structural Behavior of Serrated Cast-In Anchor Channels - A Numerical Study on the Longitudinal Loading Close to the Edge}},
  year = {2016},
  doi = {10.21012/fc9.016},
}
Figure