Surface morphology, structure and transport property of NaxCoO2 thin films grown by pulsed laser deposition

X. P. Zhang, Youshao Xiao, H. Zhou, Bing-Hao Xie, C. X. Yang, Y. G. ZhaoarXiv 2005 · DOI · arXiv

Abstract

In this paper, we report the growth of $Na_xCoO_2$ thin films by pulsed-laser deposition (PLD). It is shown that the concentration of sodium is very sensitive to the substrate temperature and the target-substrate distance due to the evaporation of sodium during the deposition. $\alpha'$-phase $Na_{0.75}CoO_2$ and $\gamma$-phase $Na_{0.71}CoO_2$ thin films can be obtained with different conditions. Correspondingly, the surface morphology of the films changes from flake-like to particle-like. The temperature dependence of resistivity for the films prepared with the optimal condition shows metallic behavior, consistent with the data of $Na_xCoO_2$ single crystals. This work demonstrates that PLD is a promising technique to get high quality $Na_xCoO_2$ thin films.

Introduction

Sodium cobalt oxide ($Na_xCoO_2$) has garnered significant interest in condensed matter physics, primarily due to its high thermoelectric power and the emergence of superconductivity when intercalated with water. As a strongly correlated electron system, it shares similarities with high-temperature superconductors. However, the fabrication of high-quality thin films—essential for device applications—is hindered by the extreme volatility of sodium. Maintaining stoichiometry during high-temperature deposition is a major hurdle, often leading to insulating or multi-phase films. This study presents the first successful growth of $Na_xCoO_2$ thin films using Pulsed Laser Deposition (PLD).

Experimental Methods

Thin films were deposited on $LaAlO_3$ (LAO) substrates using a $Na_{0.75}CoO_2$ target prepared via solid-state reaction. To counteract sodium loss, the growth parameters were meticulously tuned. Substrate temperatures were varied between $650^\circ C$ and $670^\circ C$, while the target-to-substrate distance was adjusted from $3.8$ to $4.5 cm$. Structural characterization was performed using X-ray diffraction (XRD), and surface morphology was examined via Scanning Electron Microscopy (SEM). Electrical transport properties were measured using a standard DC four-probe technique.

Structural and Morphological Analysis

The structural evolution of the films is highly dependent on the deposition conditions. XRD analysis confirms the formation of different phases based on the growth parameters. Sample A, grown at $650^\circ C$, corresponds to the hexagonal $\gamma$-phase ($Na_{0.71}CoO_2$), while Sample C, grown at $670^\circ C$, exhibits the monoclinic $\alpha'$-phase ($Na_{0.75}CoO_2$).

XRD patterns of NaxCoO2 thin films for samples a, b, and c, showing the phase evolution with growth conditions.

The surface morphology undergoes a corresponding transformation. As shown in the SEM images, the $\gamma$-phase (Sample A) consists of compact, flake-like crystals. In contrast, the $\alpha'$-phase (Sample C) displays a more particle-like morphology. Sample B represents an intermediate state where small impurity grains appear to disrupt the connectivity between the larger flakes, significantly impacting the electrical resistivity.

SEM images showing the surface morphology transition from flake-like (a) to particle-like (c) across samples grown under different conditions.

Transport Properties

The electrical properties of the films reflect their structural quality. Sample A exhibits metallic behavior with a room-temperature resistivity of $1.69 m\Omega \cdot cm$, aligning with single-crystal data. Interestingly, Sample C demonstrates a linear temperature dependence of resistivity from room temperature down to 5 K, a novel observation for the $\alpha'$-phase. Thermoelectric measurements for Sample C yielded a Seebeck coefficient of approximately $80 \mu V/^\circ C$ at $250^\circ C$, confirming the material's potential for thermoelectric applications.

Conclusion

This work establishes PLD as a viable method for producing high-quality $Na_xCoO_2$ thin films. By optimizing substrate temperature and geometry, researchers can control the phase and morphology of the resulting films. While challenges remain in achieving perfect stoichiometry and phase purity, the discovery of linear resistivity in the $\alpha'$-phase opens new avenues for studying the complex physics of sodium cobalt oxides.

Summary updated

Abstract

In this paper, we report the growth of NaxCoO2 thin films by pulsed-laser deposition (PLD). It is shown that the concentration of sodium is very sensitive to the substrate temperature and the target-substrate distance due to the evaporation of sodium during the deposition. alpha prime-phase Na0.75CoO2 and gamma- phase Na0.71CoO2 thin films can be obtained with different conditions. Correspondingly, the surface morphology of the films changes from flake-like to particle-like. The temperature dependence of resistivity for the films prepared with the optimal condition shows metallic behavior, consistent with the data of NaxCoO2 single crystals. This work demonstrates that PLD is a promising technique to get high quality NaxCoO2 thin films.
BibTeX
@misc{zhang2005surface,
  author = {X. P. Zhang and Youshao Xiao and H. Zhou and Bing-Hao Xie and C. X. Yang and Y. G. Zhao},
  title = {{Surface morphology, structure and transport property of NaxCoO2 thin films grown by pulsed laser deposition}},
  year = {2005},
  eprint = {cond-mat/0505360},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/cond-mat/0505360},
}
Figure