Exploration of growth conditions of TaAs Weyl semimetal thin film by pulsed laser deposition

Shien Li, Zefeng Lin, Wei Hu, Dayu Yan, Fucong Chen, Xinbo Bai, Beiyi Zhu, Jie Yuan, Youguo Shi, Kui Jin, Hongming Weng, Haizhong Guo

Abstract

TaAs, the first experimentally discovered Weyl semimetal material, has attracted a lot of attention due to its high carrier mobility, high anisotropy, nonmagnetic and strong interaction with light. These make it an ideal candidate for the study of Weyl fermions and the applications in quantum computation, thermoelectric devices, and photodetection. For further basic physics studies and potential applications, large-size and high-quality TaAs films are urgently needed. However, it is difficult to grow As-stoichiometry TaAs films due to the volatilization of As during the growth. To solve this problem, the TaAs films were attempted to grow on different substrates using targets with different As stoichiometric ratios by pulsed laser deposition (PLD). In this work, we have found that partial As ions of the GaAs substrate are likely to diffuse into the TaAs films during growth, which was preliminarily confirmed by the structural characterization, surface topography and composition analysis. As a result, the As content in the TaAs film is improved and the TaAs phase is achieved. Our work presents an effective method to fabricate the TaAs films by PLD, providing the possible use of the Weyl semimetal film for functional devices.

Introduction

Weyl semimetals (WSMs) like Tantalum Arsenide (TaAs) represent a frontier in condensed matter physics. Hosting massless quasiparticles known as Weyl fermions, these materials exhibit extraordinary properties, including ultra-high carrier mobility and unique topological surface states (Fermi arcs). While bulk crystals of TaAs have been successfully synthesized, the transition to high-quality thin films—essential for integration into quantum computing and optoelectronic devices—has proven challenging.

The primary obstacle in thin-film growth is the high volatility of Arsenic (As). During the high-temperature processes required for crystallization, Arsenic tends to evaporate before it can incorporate into the lattice, typically resulting in Arsenic-deficient phases such as $\text{Ta}_5\text{As}_4$ rather than the desired TaAs phase. This study explores a novel approach using Pulsed Laser Deposition (PLD) to overcome this stoichiometric imbalance.

Methods

The research team utilized a KrF excimer laser for PLD to deposit films from various targets onto a range of substrates. To address the Arsenic loss, they hypothesized that a Gallium Arsenide (GaAs) substrate could serve as a sacrificial local source of Arsenic. At the growth temperature of approximately 700 °C, Arsenic is known to diffuse out of GaAs, potentially creating an Arsenic-rich environment at the growth interface.

For comparison, films were also grown on non-Arsenic-containing substrates, including $\text{SrTiO}_3$ (STO), MgO, and $\text{MgF}_2$. Additionally, the team tested targets with varying stoichiometry ($\text{TaAs}_{1.0}$, $\text{TaAs}_{1.1}$, and $\text{TaAs}_{1.2}$) to determine if increasing the Arsenic content in the source material alone could compensate for the volatilization.

Key Results and Discussion

Phase Identification and Crystalline Quality

Structural analysis via X-ray Diffraction (XRD) confirmed that the choice of substrate is the deciding factor in achieving the pure TaAs phase. Films grown on GaAs (111) displayed clear TaAs diffraction peaks, whereas those grown on STO, MgO, and other substrates consistently resulted in the impurity phase $\text{Ta}_5\text{As}_4$. Remarkably, even using a target with 20% excess Arsenic ($\text{TaAs}_{1.2}$) on an STO substrate failed to produce the TaAs phase, highlighting that target stoichiometry cannot overcome the rapid rate of Arsenic loss during deposition.

Figure 1: (a) TaAs crystal structure. (b) XRD rocking curve showing high crystallinity (FWHM = 0.26°). (c) Successful TaAs growth on GaAs. (d-e) Failure to achieve TaAs phase on other substrates or with over-stoichiometric targets.

The crystalline quality of the TaAs films on GaAs was exceptional. The XRD rocking curve for the TaAs (112) peak yielded a Full Width at Half Maximum (FWHM) of 0.26°, indicating a high degree of orientation and structural integrity.

Mechanism of Arsenic Compensation

To verify the role of the GaAs substrate as an Arsenic source, the researchers performed annealing experiments on bare GaAs. Scanning Electron Microscopy (SEM) and Energy-Dispersive X-ray Spectroscopy (EDS) mapping revealed that at 700 °C, the GaAs surface begins to decompose, forming characteristic triangular pits as Arsenic evaporates.

Figure 2: SEM images and EDS mapping of GaAs substrates annealed for various times, showing the formation of triangular pits as Arsenic evaporates from the surface.

This "bottom-up" replenishment of Arsenic from the substrate effectively counteracts the loss of Arsenic from the film surface during PLD growth. This chemical interaction between the substrate and the film, rather than mere lattice matching, is the key to stabilizing the TaAs phase.

Conclusion

This work demonstrates the first successful fabrication of pure TaAs Weyl semimetal thin films using Pulsed Laser Deposition. By leveraging the thermal decomposition of GaAs substrates to provide a local Arsenic source, the researchers overcame the chronic problem of stoichiometry control in TaAs films. While the current films exhibit some surface roughness, the achievement of the correct crystal phase and high crystallinity marks a significant step toward the development of TaAs-based functional quantum devices. Future research will focus on optimizing surface morphology and characterizing the electronic transport properties to confirm the presence of Weyl physics in these films.

Summary updated

Abstract

TaAs, the first experimentally discovered Weyl semimetal material, has attracted a lot of attention due to its high carrier mobility, high anisotropy, nonmagnetic and strong interaction with light. These make it an ideal candidate for the study of Weyl fermions and the applications in quantum computation, thermoelectric devices, and photodetection. For further basic physics studies and potential applications, large-size and high-quality TaAs films are urgently needed. However, it is difficult to grow As-stoichiometry TaAs films due to the volatilization of As during the growth. To solve this problem, the TaAs films were attempted to grow on different substrates using targets with different As stoichiometric ratios by pulsed laser deposition (PLD). In this work, we have found that partial As ions of the GaAs substrate are likely to diffuse into the TaAs films during growth, which was preliminarily confirmed by the structural characterization, surface topography and composition analysis. As a result, the As content in the TaAs film is improved and the TaAs phase is achieved. Our work presents an effective method to fabricate the TaAs films by PLD, providing the possible use of the Weyl semimetal film for functional devices.
BibTeX
@inproceedings{li2023exploration,
  author = {Shien Li and Zefeng Lin and Wei Hu and Dayu Yan and Fucong Chen and Xinbo Bai and Beiyi Zhu and Jie Yuan and Youguo Shi and Kui Jin and Hongming Weng and Haizhong Guo},
  title = {{Exploration of growth conditions of TaAs Weyl semimetal thin film by pulsed laser deposition}},
  booktitle = {Chinese},
  year = {2023},
  doi = {10.1088/1674-1056/acb913},
}
Figure