SAR Image Generation of Ground Targets for Automatic Target Recognition Using Indirect Information

Jihee Yoo, Junmo Kim

Introduction

Automatic Target Recognition (ATR) systems are critical for modern military intelligence, enabling the rapid identification of ground targets in Synthetic Aperture Radar (SAR) imagery. However, developing robust ATR systems requires massive amounts of labeled data. While benchmark datasets like MSTAR exist, real-world applications often demand signatures for a wide variety of targets that are not publicly documented.

This research addresses two primary bottlenecks in ATR development: the lack of direct access to physical hardware for 3D scanning and the high computational cost of traditional electromagnetic (EM) simulations. The authors propose a streamlined pipeline that utilizes "indirect information"—such as photos and 2D drafts—to generate high-fidelity SAR image databases, significantly accelerating the development cycle.

Methodology

The proposed framework integrates three key innovations to bridge the gap between simulation and reality.

Indirect 3D CAD Modeling

To overcome the inability to scan adversary hardware directly, the authors developed a workflow to reverse-engineer 3D models from 2D blueprints, multi-angle photographs, and hobbyist plastic models. Validation of this approach using an LVT-P7 vehicle demonstrated an average surface discrepancy of less than 64 mm compared to a high-precision laser scan, proving that indirect sources can yield sufficiently accurate models for SAR simulation.

Efficient Bistatic Image Formation

Traditional monostatic ray tracing is computationally expensive. The authors adopted a bistatic concept based on the Shooting-and-Bouncing-Ray (SBR) technique. By performing ray tracing once to obtain scattered field data across an angular range, they decoupled the ray tracing from specific look-angles, drastically reducing computation time.

Validation via Similarity Metrics

A major innovation is the use of the Mean Structural Similarity Index (MSSIM) as a proxy for validation. Traditionally, verifying a simulated database requires training a full classifier to check recognition rates ($P_{ID}$), which is time-consuming. The authors demonstrate that MSSIM correlates strongly with actual ATR performance, allowing for rapid iterative refinement of CAD models.

Comparison of (a) traditional validation using identification rates and (b) the proposed workflow using a similarity index proxy.

Datasets and Validation

The study utilized several datasets for validation:

  • MSTAR: Used as the primary benchmark for comparing simulated T-72 tank images against real-world measured data.
  • SLICY: A geometric "Standard Laboratory Index Card" target used to validate the EM prediction algorithm's accuracy.
  • LVT-P7: Used to validate the indirect CAD modeling process against a ground-truth laser scan.

Results and Discussion

The proposed bistatic SBR approach achieved a significant performance boost, generating a single target image in less than 23 seconds—a 30x speedup over the traditional monostatic approach (12 minutes).

A sample database of generated SAR images for a target across various orientations.

When tested against the MSTAR dataset, simulated images derived from detailed CAD models achieved a recognition rate ($P_{ID}$) of 90.9%. Furthermore, the study confirmed that as CAD model detail increases, both MSSIM and recognition rates increase monotonically, validating the use of similarity indices for "on-the-fly" database generation. The research also highlighted that simulated data can effectively augment small real-world datasets, improving recognition rates when measured data is scarce.

Conclusion

This paper presents a viable path for generating high-fidelity SAR training data using indirect information. By combining efficient bistatic simulation with structural similarity validation, the authors provide a framework that is both fast and accurate. Future work will focus on improving ground range projection scaling and incorporating more complex environmental factors, such as soil moisture and vegetation, to further enhance simulation realism.

Summary updated

Abstract

The effectiveness of using the simulated synthetic aperture radar (SAR) images of military targets in databases for automatic target recognition (ATR) is widely known. However, for simulated target images to be useful, they must be sufficiently similar to measured images; otherwise, they can degrade ATR performance. Two factors affect the quality of simulated SAR images: precision of the associated computer-aided design (CAD) model of the target and the accuracy and speed of the numerical techniques used to solve the electromagnetic problems in SAR image generation. In this study, a method for the 3D CAD modeling of the target is proposed; this method can be used when direct access to the target is not feasible and only indirect information is available. Further, a bistatic image formation concept based on the shooting-and-bouncing-ray technique is adopted; this concept helps achieve an accuracy comparable to that of the monostatic method. Moreover, it helps achieve a highly enhanced computation speed. In combination, these proposals provide an efficient and fast method to generate a database of simulated SAR images that can effectively support ATR activities. We demonstrate the effectiveness of the proposed method by comparing the simulated SAR images with the measured ones using structural similarity as a similarity measure; further, we evaluate the recognition rate obtained with the simulated images. We show that the used similarity measure bears a strong relation with the recognition rate, which is an aspect that may further contribute to considerable time savings when validating and refining simulated image databases.
BibTeX
@article{yoo2021sar,
  author = {Jihee Yoo and Junmo Kim},
  title = {{SAR Image Generation of Ground Targets for Automatic Target Recognition Using Indirect Information}},
  journal = {IEEE Access},
  year = {2021},
  doi = {10.1109/access.2021.3057455},
}
Figure