Abstract
Full-duplex communication has the potential to substantially increase the throughput in wireless networks. However, the benefits of full-duplex are still not well understood. In this paper, we characterize the full-duplex rate gains in both single-channel and multi-channel use cases. For the single-channel case, we quantify the rate gain as a function of the remaining self-interference and SNR values. We also provide a sufficient condition under which the sum of uplink and downlink rates on a full-duplex channel is concave in the transmission power levels. Building on these results, we consider the multi-channel case. For that case, we introduce a new realistic model of a small form-factor (e.g., smartphone) full-duplex receiver and demonstrate its accuracy via measurements. We study the problem of jointly allocating power levels to different channels and selecting the frequency of maximum self-interference suppression, where the objective is maximizing the sum of the rates over uplink and downlink OFDM channels. We develop a polynomial time algorithm which is nearly optimal in practice under very mild restrictions. To reduce the running time, we develop an efficient nearly-optimal algorithm under the high SINR approximation. Finally, we demonstrate via numerical evaluations the capacity gains in the different use cases and obtain insights into the impact of the remaining self-interference and wireless channel states on the performance.
Introduction
The primary hurdle for Full-Duplex (FD) communication—sending and receiving on the same frequency simultaneously—is Self-Interference (SI). The transmitter’s signal is often billions of times stronger than the incoming signal it is trying to receive. While researchers have developed various Self-Interference Cancellation (SIC) techniques, most theoretical studies assume SIC is either perfect or uniform across all frequencies. In reality, especially for compact devices like smartphones, SIC is frequency-selective. Physical constraints of integrated circuits mean cancellation is strongest at a specific frequency and degrades as you move away from it. This paper addresses the challenge of resource allocation when hardware limitations make the ability to "hear" dependent on both frequency and transmission power.
Modeling Practical Full-Duplex Hardware
To bridge the gap between theory and practice, the authors developed a new mathematical model for frequency-selective SIC. This model is based on measurements from a custom-designed Radio Frequency Integrated Circuit (RFIC) and commercial circulators.
As shown in the transceiver architecture above, the system utilizes both RF and digital cancellation paths. The authors analyzed the "sum rate" function (the total speed of uplink and downlink) and proved that while the problem is generally non-convex, it is biconcave under certain mild conditions. This structural insight makes the complex optimization problem computationally tractable for real-world applications.
Resource Allocation Algorithms
Building on their hardware model, the authors developed two primary algorithms to optimize power levels across OFDM channels and select the optimal "center frequency" for SIC:
- MAXIMUMRATE: A polynomial-time algorithm that jointly optimizes power levels and the frequency of maximum suppression.
- HSINR-MAXIMUMRATE: A highly efficient version optimized for high Signal-to-Interference-plus-Noise Ratio (SINR) environments, common in modern high-speed wireless links. This algorithm runs in $O(K \log(1/\epsilon))$ time, where $K$ is the number of channels, making it suitable for real-time implementation.
Experimental Validation and Key Results
The proposed models and algorithms were validated using a combination of custom hardware measurements and numerical simulations.
Key findings from the study include:
- Model Accuracy: The frequency-selective SI model closely matched experimental measurements from the custom RFIC hardware shown above.
- The "All or Nothing" Power Rule: For single-channel links, if FD is beneficial at all compared to traditional Time-Division Duplexing (TDD), the optimal strategy is almost always to transmit at maximum power.
- Capacity Gains: FD can significantly extend the capacity region over TDD at high SNRs. However, if SIC is poor, the gain can drop to zero or even become a loss compared to TDD.
- Practical Simplicity: In multi-channel systems, equal power allocation is nearly as effective as complex, optimized allocation once the system reaches a regime where FD is useful.
Conclusion
This work provides a rigorous foundation for understanding FD gains in practical hardware. Future work will focus on extending these frequency-selective models to Multiple-Input Multiple-Output (MIMO) systems and integrating these physical-layer insights into Media Access Control (MAC) layer protocols to manage inter-node interference in dense networks.
Summary updated