Photoconductive Effects in Single Crystals of BaZrS3

Boyang Zhao, Huandong Chen, Ragib Ahsan, Fei Hou, Eric R. Hoglund, Shantanu Singh, Maruda Shanmugasundaram, Huan Zhao, Andrey Krayev, Han Htoon, Patrick E. Hopkins, Jan Seidel, Rehan Kapadia, Jayakanth Ravichandran

TL;DR

This paper investigates the impact of processing-induced defects on the photoconductive properties of BaZrS₃ single crystals, a promising semiconductor for optoelectronic applications. They found that mechanical polishing introduces detrimental defects, leading to trap-dominated responses, while cleaving the crystals significantly improves their optoelectronic performance by minimizing these defects.

What Problem Does This Paper Address?

Chalcogenide perovskites, like BaZrS₃, are gaining attention for their potential in high-efficiency photovoltaic devices. However, a critical factor influencing their performance – the role of defects in generating and collecting photoexcited carriers – has not been thoroughly explored experimentally. This paper aims to bridge this knowledge gap by systematically studying how processing-induced defects affect the photoconductive properties of BaZrS₃ single crystals, ultimately seeking to understand the limitations on achieving high photon-to-electron conversion efficiency.

Methods

The researchers employed a multi-faceted approach to characterize the BaZrS₃ crystals and their optoelectronic properties:

  • Crystal Growth: BaZrS₃ single crystals were grown using a BaCl₂ flux method, with a focus on optimizing the cooling rate to achieve larger crystals.
  • Surface Characterization: Kelvin Probe Microscopy (KPFM) was used to measure the work function of the BaZrS₃ surface and to study surface photovoltage (SPV) under illumination.
  • Electrical Contact Fabrication: Two methods were used to create electrical contacts:
  • Mechanical Polishing: This involved removing the native surface oxide layer through polishing.
  • Cleavage: This method exposed fresh crystal surfaces for contact deposition.
  • Photoconductivity Measurements: Two-terminal devices were fabricated to study the current-voltage (I-V) characteristics under dark and illuminated conditions. Time-resolved photocurrent measurements were also performed.
  • Scanning Photocurrent Microscopy (SPCM): This technique was used to map the spatial distribution of photocurrent across the device, providing insights into carrier transport.
  • Electron Microscopy: Scanning Transmission Electron Microscopy (STEM) was employed to visualize and analyze the microstructural defects introduced by mechanical polishing.

Datasets

Not discussed in the paper.

Key Insights and Ideas

  • Surface Photovoltage Indicates p-type Behavior: The observation of a positive surface photovoltage, consistent with a decreasing work function under illumination, suggests that BaZrS₃ behaves like a p-type semiconductor.
  • Mechanical Polishing Introduces Detrimental Defects: The process of mechanically polishing BaZrS₃ to remove surface oxides creates significant deformation-induced grain boundaries and other extended defects. These defects act as traps, dominating the photoconductive response and hindering efficient carrier collection.
  • Cleavage Significantly Improves Performance: In contrast to polished samples, cleaved BaZrS₃ crystals, which have fewer processing-induced defects, exhibit greatly improved optoelectronic properties, including faster photocurrent rise and decay times.
  • Defect Control is Crucial for High Efficiency: The study highlights that controlling crystal growth and, more importantly, contact fabrication methods to minimize defect formation is paramount for realizing the full potential of BaZrS₃ and other chalcogenide perovskites in optoelectronic devices.

Key Results

  • Ohmic Contacts Achieved: The researchers successfully fabricated ohmic or nearly ohmic electrical contacts to BaZrS₃ single crystals using both polishing and cleavage methods.
  • Polished Crystals Show Trap-Dominated Response: Two-terminal devices made from polished BaZrS₃ exhibited a trap-dominated photocurrent response, characterized by slow rise and decay times (18 s and 26 s, respectively). The power law exponent for photocurrent generation was low (θ = 0.29), indicating significant trap influence.
  • Cleaved Crystals Show Improved Response: Cleaved BaZrS₃ crystals showed a significantly improved photocurrent response with much faster rise and decay times (2 s and 2 s, respectively), comparable to epitaxial films. The power law exponent was higher (θ = 0.67), suggesting more efficient carrier generation and collection.
  • STEM Reveals Defect Structures: STEM imaging confirmed the presence of numerous planar defects, such as dislocations, stacking faults, and grain boundaries, beneath the mechanically polished surface, extending up to ~300 nm. Cleaved surfaces, however, showed minimal defects.

Limitations and Future Work

  • Device Geometry Optimization: The authors acknowledge that the device geometries used in their study were neither optimized nor exactly comparable, which might influence the quantitative results.
  • Orthorhombic BaZrS₃ Cleavage: The orthorhombic structure of BaZrS₃ does not possess an easy-to-cleave crystalline plane, meaning cleavage surfaces can be uneven, potentially introducing some defects.
  • Future Directions: The paper suggests that further improvements in optoelectronic performance can be achieved through:
  • Electrode Patterning: Designing more efficient electrode geometries.
  • Surface Passivation: Applying passivation layers to reduce surface recombination.
  • Heterojunctions: Exploring electron/hole heterojunctions.
  • Defect Control: Continued focus on defect-controlled crystal growth and contact fabrication techniques.

The study concludes that optimizing contacts, surfaces, and device geometry is the critical next step for developing high-efficiency optoelectronic and photovoltaic devices based on BaZrS₃ and similar chalcogenide perovskites.

Summary updated

Abstract

Chalcogenide perovskites, such as BaZrS3, are emerging semiconductors with the potential for high photovoltaic power conversion efficiency. The role of defects in the efficiency of the generation and collection of photoexcited carriers has not been experimentally investigated extensively. We studied the effect of processing-induced defects on the photoconductive properties of single crystals of BaZrS3. We achieved Ohmic contacts to single crystals of BaZrS3 and observed positive surface photovoltage, which is typically observed in p-type semiconductors. However, mechanical polishing of BaZrS3 to remove the surface oxide leads to dense deformation grain boundaries and to trap-dominated photoconductive response. In comparison, Ohmic contacts achieved in cleaved crystals leave fewer deformation defects and greatly improve optoelectronic properties. Defect-controlled crystal growth and contact fabrication are potentially limiting factors for achieving a high photon-to-excited-electron conversion efficiency in BaZrS3.
BibTeX
@inproceedings{zhao2024photoconductive,
  author = {Boyang Zhao and Huandong Chen and Ragib Ahsan and Fei Hou and Eric R. Hoglund and Shantanu Singh and Maruda Shanmugasundaram and Huan Zhao and Andrey Krayev and Han Htoon and Patrick E. Hopkins and Jan Seidel and Rehan Kapadia and Jayakanth Ravichandran},
  title = {{Photoconductive Effects in Single Crystals of BaZrS<sub>3</sub>}},
  booktitle = {ACS},
  year = {2024},
  doi = {10.1021/acsphotonics.3c01563},
}
Figure