Perpetual Reconfigurable Intelligent Surfaces Through In-Band Energy Harvesting: Architectures, Protocols, and Challenges

Konstantinos Ntontin, Alexandros-Apostolos A. Boulogeorgos, Sergi Abadal, Agapi Mesodiakaki, Symeon Chatzinotas, Björn E. Ottersten

TL;DR

This paper introduces the concept of "perpetual" Reconfigurable Intelligent Surfaces (RISs) that sustain themselves by harvesting energy from the very communication signals they reflect. By moving from power-hungry FPGA controllers to integrated, low-power ASICs and utilizing a "unit-cell splitting" protocol, the authors demonstrate a path toward massive, maintenance-free 6G deployments that don't require power cables or batteries.

What Problem Does This Paper Address?

As we move toward 6G, we are shifting into millimeter-wave (mmWave) and Terahertz (THz) frequencies. These bands offer massive bandwidth but suffer from a major flaw: they are easily blocked by walls, trees, or even people. Reconfigurable Intelligent Surfaces (RISs) are a promising solution—they act as "smart mirrors" that can steer signals around obstacles.

However, there is a catch. While RISs don't have power amplifiers like traditional relays, their electronic controllers (usually FPGAs) still require significant power. In a future where we might need thousands of RISs plastered across a city, wiring every single one to the power grid is a logistical nightmare, and using batteries would lead to an impossible maintenance cycle. The authors tackle the "powering problem" by proposing a self-sustaining architecture.

Methods

The authors propose a shift in how RISs are built and operated:

  1. Integrated Architecture vs. FPGA: They argue that traditional FPGA-based controllers are too power-hungry for autonomous operation. Instead, they propose an integrated architecture where tiny, custom-made Application-Specific Integrated Circuits (ASICs) are embedded directly into the surface. These ASICs use asynchronous logic to minimize power consumption to the microwatt level.
  2. In-Band Energy Harvesting (EH): The RIS captures a portion of the incident electromagnetic (EM) waves used for communication and converts them into DC power via rectifying circuits to charge an internal battery.
  3. Harvesting Protocols: They compare two ways to balance communication and power:
  4. Time-splitting: The RIS spends a fraction of each time frame exclusively harvesting energy (acting as a perfect absorber) and the rest of the time reflecting signals.
  5. UC-splitting (Unit-Cell splitting): A subset of the RIS elements is dedicated to harvesting energy while the remaining elements simultaneously reflect the signal to the user.

Datasets

This is a theoretical and simulation-based study. The authors used a set of parameters derived from state-of-the-art hardware research:

  • Carrier Frequency: 28 GHz (mmWave).
  • Power Consumption: Based on a specific ASIC design from recent literature (Petrou & Georgiou, 2022) that controls 4 unit cells.
  • Channel Model: Free-space for the Transmitter-RIS link and Rician fading for the RIS-Receiver link.
  • Energy Model: Based on established RF-to-DC conversion efficiency models for Schottky diode-based rectifiers.

Key Insights and Ideas

  • The Static Power Bottleneck: The biggest hurdle isn't the energy used to change the RIS state (dynamic power), but the energy required just to keep the controller on (static power). If static power exceeds a few dozen microwatts, the RIS can't harvest enough energy to stay "perpetual."
  • UC-Splitting Wins: The "UC-splitting" protocol is significantly more efficient than "time-splitting." By allowing communication and harvesting to happen at the same time, it maintains a higher average data rate and is more resilient to higher controller power demands.
  • The "Perpetual" Threshold: The paper identifies a clear trade-off: as the power requirement of the electronics increases, the communication rate drops because more of the surface (or more time) must be dedicated to harvesting rather than reflecting.

Key Results

  • Performance Superiority: In simulations, the UC-splitting protocol consistently outperformed time-splitting. For example, at an ASIC static power consumption of $32 \mu W$, UC-splitting maintained a data rate of roughly 2 Gbps, while time-splitting dropped significantly lower.
  • Viability: The study shows that if ASIC power consumption can be kept below $\sim 60 \mu W$, a perpetual RIS is theoretically possible in a typical mmWave cell setup (1W transmit power at 18 meters).
  • Dynamic vs. Static: As the complexity of the RIS increases, the ratio of dynamic-to-static power decreases, reinforcing the need for ultra-low-power "sleep" modes in controller designs.

Limitations and Future Work

  • Hardware Realities: While the paper uses realistic ASIC parameters, building a large-scale surface that integrates thousands of these chips with efficient RF-combining networks remains a significant manufacturing challenge.
  • Channel Modeling: The current study assumes relatively simple channel models. Future work needs to account for more complex THz environments and the "randomness" of energy arrivals in highly mobile scenarios.
  • Multi-Band Harvesting: The authors suggest that future RISs might harvest energy from lower, more ubiquitous frequencies (like sub-6 GHz) while reflecting high-frequency mmWave signals, potentially increasing the energy "budget."
  • Network Planning: There is a need for new deployment strategies—placing RISs not just where they help the signal most, but where they can receive enough "power illumination" to stay alive.

Summary updated

Abstract

Reconfigurable intelligent surfaces (RISs) are considered a key enabler of highly energy-efficient 6G and beyond networks. This property arises from the absence of power amplifiers in the structure, in contrast to active nodes, such as small cells and relays. However, a certain amount of power is still required for RIS operation. To improve their energy efficiency further, we propose the notion of perpetual RISs, which secure the power needed to supply their functionalities through wireless energy harvesting (EH) of impinging transmitted electromagnetic (EM) signals. Toward this, we initially explain the rationale behind such RIS capability and proceed with a presentation of the main RIS controller architecture that can realize this vision under an in-band EH consideration. Furthermore, we present a typical EH architecture, followed by two harvesting protocols. Subsequently, we study the performance of the two protocols under a typical communications scenario. Finally, we elaborate on the main research challenges governing the realization of large-scale networks with perpetual RISs.
BibTeX
@inproceedings{ntontin2024perpetual,
  author = {Konstantinos Ntontin and Alexandros-Apostolos A. Boulogeorgos and Sergi Abadal and Agapi Mesodiakaki and Symeon Chatzinotas and Björn E. Ottersten},
  title = {{Perpetual Reconfigurable Intelligent Surfaces Through In-Band Energy Harvesting: Architectures, Protocols, and Challenges}},
  booktitle = {IEEE Veh. Technol. Mag},
  year = {2024},
  url = {https://openreview.net/forum?id=2uuTjkKbK8},
}

Loading related content...

Figure