Abstract
Hybrid analog and digital beamforming is a promising candidate for large-scale mmWave MIMO systems because of its ability to significantly reduce the hardware complexity of the conventional fully-digital beamforming schemes while being capable of approaching the performance of fully-digital schemes. Most of the prior work on hybrid beamforming considers narrowband channels. However, broadband systems such as mmWave systems are frequency-selective. In broadband systems, it is desirable to design common analog beamformer for the entire band while employing different digital beamformers in different frequency sub-bands. This paper considers hybrid beamforming design for systems with OFDM modulation. First, for a SU-MIMO system where the hybrid beamforming architecture is employed at both transmitter and receiver, we show that hybrid beamforming with a small number of RF chains can asymptotically approach the performance of fully-digital beamforming for a sufficiently large number of transceiver antennas due to the sparse nature of the mmWave channels. For systems with a practical number of antennas, we then propose a unified heuristic design for two different hybrid beamforming structures, the fully-connected and the partially-connected structures, to maximize the overall spectral efficiency of a mmWave MIMO system. Numerical results are provided to show that the proposed algorithm outperforms the existing hybrid beamforming methods and for the fully-connected architecture the proposed algorithm can achieve spectral efficiency very close to that of the optimal fully-digital beamforming but with much fewer RF chains. Second, for the MU-MISO case, we propose a heuristic hybrid percoding design to maximize the weighted sum rate in the downlink and show numerically that the proposed algorithm with practical number of RF chains can already approach the performance of fully-digital beamforming.
Introduction
Millimeter-wave (mmWave) communications are essential for meeting the high data rate demands of 5G and 6G networks. To overcome the significant path loss at these frequencies, large-scale antenna arrays are deployed to provide high beamforming gains. However, the traditional fully-digital beamforming architecture, which requires a dedicated radio frequency (RF) chain for each antenna element, is prohibitively expensive and power-hungry for massive arrays. Hybrid beamforming architectures emerge as a cost-effective alternative, partitioning the beamforming process into a low-dimensional digital stage and a high-dimensional analog stage.
System Model and the Wideband Challenge
In wideband systems employing Orthogonal Frequency Division Multiplexing (OFDM), the channel is frequency-selective. While digital beamformers can be optimized for each subcarrier, the analog beamformer—implemented via phase shifters—is typically frequency-flat, meaning a single analog configuration must serve the entire frequency band. This creates a significant design challenge: how to optimize a common analog stage that performs well across all subcarriers.
The research considers two primary hardware topologies for the analog stage:
- Fully-Connected Structure: Each RF chain is connected to all antennas through phase shifters.
- Partially-Connected (Sub-array) Structure: Each RF chain is connected to only a subset of antennas, reducing hardware complexity further at the cost of some flexibility.
Proposed Methodology
The authors propose a unified heuristic design to maximize spectral efficiency. The approach is grounded in the observation that mmWave channels are spatially sparse, meaning signals primarily propagate along a limited number of paths.
Asymptotic Analysis
The paper first proves that as the number of antennas grows to infinity, a hybrid system with a limited number of RF chains can asymptotically achieve the same performance as a fully-digital system. This is possible because the number of dominant spatial paths in mmWave channels is typically much smaller than the number of antennas.
The Average Covariance Heuristic
For practical antenna counts, the authors introduce a heuristic that designs the analog beamformer based on the average of the channel covariance matrices across all OFDM subcarriers. This captures the dominant spatial directions common to the entire band. An iterative coordinate descent algorithm is then used to solve the non-convex optimization problem under the constant-modulus constraint of the phase shifters. Once the analog stage is fixed, the digital precoders are optimized per subcarrier using standard techniques like water-filling for single-user scenarios or WMMSE for multi-user scenarios.
Key Results
Numerical evaluations using a stochastic geometric channel model demonstrate several key findings:
- Efficiency: In a 64x32 SU-MIMO setup, the proposed hybrid design achieves spectral efficiency nearly identical to the optimal fully-digital system while using significantly fewer RF chains.
- Performance Gain: The heuristic outperforms existing state-of-the-art hybrid beamforming methods by approximately 2dB in practical scenarios.
- Multi-User Scalability: For MU-MISO, the algorithm shows that a base station with 16 RF chains and 64 antennas can match the performance of a fully-digital 64-antenna system when serving 4 users.
Conclusion
This work provides a robust framework for designing hybrid beamforming in wideband mmWave systems. By leveraging the spatial sparsity of mmWave channels and employing an "average covariance" heuristic, the proposed methods bridge the gap between low-cost hybrid hardware and high-performance fully-digital systems. Future research will likely address the challenges of imperfect channel state information and the integration of user scheduling into the beamforming design.
Summary updated