High resolution multispectral spatial light modulators based on tunable Fabry-Perot nanocavities

Shampy Mansha, Parikshit Moitra, Xu Jia, Tobias W. W. Maß, Rasna Maruthiyodan Veetil, Xinan Liang, Shiqiang Li, Ramón Paniagua‐Domínguez, Arseniy I. Kuznetsov

This paper presents a significant leap in the field of wavefront manipulation, introducing a new architecture for Spatial Light Modulators (SLMs) that achieves high resolution and multispectral operation simultaneously. By utilizing tunable Fabry-Perot nanocavities, the researchers have bypassed the fundamental scaling laws that have stalled the miniaturization of commercial liquid crystal displays for nearly a decade.

TL;DR

Researchers have developed a multispectral Spatial Light Modulator (SLM) using liquid-crystal-tunable Fabry-Perot nanocavities that achieves full $2\pi$ phase control with sub-micron pixel pitches. This design overcomes the resolution limits of traditional LCoS devices and the monochromatic constraints of metasurfaces, enabling high-efficiency RGB beam steering and tunable lensing.

What Problem Does This Paper Address?

Spatial Light Modulators are the "engines" behind technologies like holographic displays, AR/VR headsets, and optical communications. Currently, the gold standard is Liquid Crystal on Silicon (LCoS). However, LCoS technology faces a "pixel size floor." To achieve a full $2\pi$ phase shift, LCoS devices require a relatively thick layer of liquid crystal (LC). As pixels get smaller, the high voltages required to drive these thick layers cause "inter-pixel crosstalk"—where the electric field from one pixel bleeds into its neighbor—rendering the phase profile unpredictable. Consequently, commercial pixel sizes have been stuck at $>3\mu m$.

While newer "metasurface" SLMs can be much smaller, they are typically monochromatic, meaning they only work for a single color. The challenge addressed here is creating a device that is both high-resolution (small pixels) and multispectral (works across the visible spectrum).

Methods

The authors designed a Fabry-Perot (FP) nanocavity SLM. The structure consists of:

  • Distributed Bragg Reflectors (DBRs): Two partially reflective mirrors made of alternating layers of $TiO_2$ and $SiO_2$.
  • Active Layer: A very thin (530 nm) layer of nematic liquid crystal sandwiched between the DBRs.
  • Electrodes: A common ITO top electrode and a patterned 1D array of 96 aluminum bottom electrodes (1 $\mu m$ width).

The key innovation is using the resonance shift of the FP cavity to generate phase. By applying a voltage, the LC molecules reorient, changing the refractive index and shifting the cavity's resonant frequency. This shift provides a large phase modulation ($2\pi$) even with an extremely thin LC layer.

To handle the remaining inter-pixel crosstalk and fabrication imperfections, the team employed a "software-defined" approach, using the DIRECT-L (Locally biased DIviding RECTangles) optimization algorithm to find the ideal voltage profiles for specific optical functions in real-time.

Datasets

Not discussed in the paper. The study relies on original experimental measurements and full-wave numerical simulations (FDTD).

Key Insights and Ideas

  • Decoupling Phase from Thickness: In traditional optics, phase delay is directly proportional to material thickness. By using a resonant cavity, the authors "amplify" the phase response, allowing them to shrink the LC layer to sub-micron levels. This reduction in thickness is what finally enables pixel miniaturization without catastrophic crosstalk.
  • Multispectral by Design: The DBRs and cavity height were specifically engineered to support multiple resonances across the visible spectrum. This allows the device to operate at Red, Green (shifted to Orange in the prototype), and Blue wavelengths simultaneously.
  • Algorithmic Calibration: The researchers recognized that at the 1 $\mu m$ scale, hardware will never be perfect. By integrating a global optimization loop into the device's operation, they can "calibrate out" fabrication errors and crosstalk, achieving higher efficiencies than would be possible with manual voltage settings.

Key Results

  • Pixel Pitch: Achieved a pitch of 1.14 $\mu m$, roughly 3x smaller than the best commercial LCoS devices.
  • Phase Range: Demonstrated near $2\pi$ phase shifts for Blue (503 nm) and Orange (596 nm), and $\sim1.5\pi$ for Red (662 nm).
  • Beam Steering: Achieved a wide Field of View (FOV) of $18^\circ$ with absolute efficiencies exceeding 40%.
  • Tunable Lensing: Demonstrated a cylindrical lens with a tunable focal distance and a Numerical Aperture (NA) up to 0.15, with efficiencies around 27%.

Limitations and Future Work

  • 1D vs. 2D: The current prototype is a 1D linear array (96 pixels). The authors note that extending this to a 2D array is the next logical step, likely requiring standard CMOS backplane integration.
  • Efficiency Gaps: While 40% efficiency is impressive for a prototype, it still lags behind some specialized monochromatic metasurfaces. The authors suggest that further optimizing the lens profiles using machine learning could bridge this gap.
  • Crosstalk Mitigation: Although reduced, crosstalk still exists. The authors propose that placing the electrodes inside the dielectric mirrors could further isolate pixels and allow for even smaller sizes.

Summary updated

Abstract

Spatial light modulators (SLMs) are the most relevant technology for dynamic wavefront manipulation. They find diverse applications ranging from novel displays to optical and quantum communications. Among commercial SLMs for phase modulation, Liquid Crystal on Silicon (LCoS) offers the smallest pixel size and, thus, the most precise phase mapping and largest field of view (FOV). Further pixel miniaturization, however, is not possible in these devices due to inter-pixel cross-talks, which follow from the high driving voltages needed to modulate the thick liquid crystal (LC) cells that are necessary for full phase control. Newly introduced metasurface-based SLMs provide means for pixel miniaturization by modulating the phase via resonance tuning. These devices, however, are intrinsically monochromatic, limiting their use in applications requiring multi-wavelength operation. Here, we introduce a novel design allowing small pixel and multi-spectral operation. Based on LC-tunable Fabry-Perot nanocavities engineered to support multiple resonances across the visible range (including red, green and blue wavelengths), our design provides continuous 2π phase modulation with high reflectance at each of the operating wavelengths. Experimentally, we realize a device with 96 pixels (~1 μm pitch) that can be individually addressed by electrical biases. Using it, we first demonstrate multi-spectral programmable beam steering with FOV~18° and absolute efficiencies exceeding 40%. Then, we reprogram the device to achieve multi-spectral lensing with tunable focal distance and efficiencies ~27%. Our design paves the way towards a new class of SLM for future applications in displays, optical computing and beyond.
BibTeX
@inproceedings{mansha2022high,
  author = {Shampy Mansha and Parikshit Moitra and Xu Jia and Tobias W. W. Maß and Rasna Maruthiyodan Veetil and Xinan Liang and Shiqiang Li and Ramón Paniagua‐Domínguez and Arseniy I. Kuznetsov},
  title = {{High resolution multispectral spatial light modulators based on tunable Fabry-Perot nanocavities}},
  booktitle = {Light},
  year = {2022},
  doi = {10.1038/s41377-022-00832-6},
}

Loading related content...

Figure