Abstract
We propose an approach to estimate the end-to-end GSNR accurately in a short time when a data center interconnect (DCI) network operator receives a service request from users. Instead of measuring the GSNR at the operational route and wavelength for the entire optical path, we apply a Quality of Transmission (QoT) probe channel link-by-link at a convenient wavelength/modulation format. Assuming connections between coherent transceivers of various frequency ranges and modulators, we propose a new device software architecture where the DCI network operator optimizes the transmission mode with high accuracy using standard parameters like Bit Error Rate (BER). Experimental results from three different routes (32 km to 122 km) in the C-band confirmed an estimation accuracy of 0.6 dB. Using field fibers in the NSF COSMOS testbed and a Linux-based software architecture, fast WDM provisioning was completed within 6 minutes with a Q-factor error of approximately 0.7 dB.
Introduction
As cloud services and mobile edge computing (MEC) expand, the demand for fast and flexible connections between distributed data centers (DCI) and exchanges (DCX) has intensified. Traditionally, establishing a Wavelength Division Multiplexing (WDM) link requires exhaustive Quality of Transmission (QoT) measurements for specific paths and wavelengths. In complex metro networks characterized by many-to-many connections and diverse multi-vendor hardware, this "measure everything" approach is prohibitively slow.
Furthermore, network operators often lack internal characteristics of user transceivers (TRx), complicating signal degradation predictions. The industry currently lacks a unified management framework for these multi-vendor environments that supports rapid, automated provisioning and restoration.
Proposed Methodology
To address these challenges, we propose a two-pronged solution:
- Link-by-Link GSNR Estimation: Rather than measuring end-to-end (EtE) Generalized Signal-to-Noise Ratio (GSNR) for every route, we measure individual links using a "probe" channel. We then employ a mathematical model based on Gaussian noise approximation to sum the reciprocal GSNRs of these links, including internal transceiver noise, to predict total EtE signal quality.
- Open Software Architecture: We developed a Linux-based transmission software stack utilizing the Goldstone Network Operating System (NOS) and the Transponder Abstraction Interface (TAI). By using Docker containers, a carrier's controller can interact with user transceivers via a "Carrier Agent." This allows for the extraction of hardware characteristics (as JSON files) without exposing proprietary code, enabling the controller to automatically calculate optimal transmission modes (e.g., 400G 16QAM vs. 200G QPSK).
Experimental Evaluation
The study utilized real-world data from the NSF COSMOS Testbed in Harlem, New York City, and Manhattan field fibers (32 km and 8 km loops) provided by Boldyn and CrownCastle. The hardware setup included commercial 400G CFP2-DCO transceivers from Fujitsu and Lumentum, featuring both Indium Phosphide (InP) and Silicon Photonics (SiP) modulators.
Key insights from the trial include:
- Sum of Reciprocals Accuracy: EtE GSNR can be reliably predicted by summing reciprocal noise contributions from transceivers, amplifiers (ASE noise), and fiber nonlinearities.
- Wavelength Independence: In metro-scale networks (~200km), wavelength-dependent error is minimal (~0.2 dB), allowing a probe at one C-band frequency to serve as a proxy for the entire band.
Results and Discussion
The field trials yielded several significant results:
- High Accuracy: The discrepancy between estimated and actual measured EtE GSNR was only 0.6 dB.
- Rapid Provisioning: The end-to-end process—from hardware data gathering to link measurement and path establishment—was completed in 351 seconds (under 6 minutes).
- Automated Mode Selection: The system successfully provisioned a 400G DP-16QAM path for shorter routes and two 200G DP-QPSK paths for longer, more degraded routes automatically.
Conclusion
This work demonstrates that link-by-link probing combined with an open, containerized software architecture can drastically reduce provisioning times for metro-scale optical networks. While currently focused on the C-band and CFP2-DCO modules, future work will explore C+L multi-band systems and other form factors like QSFP-DD to further enhance interoperability and scalability in multi-vendor DCX environments.
Summary updated