Abstract
Modern systems will increasingly rely on energy harvested from their environment. Such systems utilize batteries to smoothen out the random fluctuations in harvested energy. These fluctuations induce highly variable battery charge and discharge rates, which affect the efficiencies of practical batteries that typically have non-zero internal resistances. In this paper, we study an energy harvesting communication system using a finite battery with non-zero internal resistance. We adopt a dual-path architecture, in which harvested energy can be directly used, or stored and then used. In a frame, both time and power can be split between energy storage and data transmission. For a single frame, we derive an analytical expression for the rate optimal time and power splitting ratios between harvesting energy and transmitting data. We then optimize the time and power splitting ratios for a group of frames, assuming non-causal knowledge of harvested power and fading channel gains, by giving an approximate solution. When only the statistics of the energy arrivals and channel gains are known, we derive a dynamic programming based policy and, propose three sub-optimal policies, which are shown to perform competitively. In summary, our study suggests that battery internal resistance significantly impacts the design and performance of energy harvesting communication systems and must be taken into account.
Introduction
Energy harvesting (EH) is a cornerstone of sustainable IoT and remote sensing, promising near-perpetual operation. However, environmental energy sources like solar or vibration are inherently erratic. To manage this, devices use batteries as buffers. Standard academic models often assume "ideal" batteries with constant efficiency, but real-world hardware is limited by internal resistance ($r$). When batteries are charged or discharged rapidly, energy is lost as heat ($I^2r$ losses), making battery efficiency rate-dependent. This paper investigates how these physical imperfections change the optimal strategies for energy management and data transmission.
System Architecture and Methods
The authors model a dual-path architecture designed to mitigate battery losses. As shown in Figure 2, harvested power $c$ can be split: a fraction $\alpha c$ is sent directly to the transmitter (the zero-loss path), while the remainder $(1-\alpha)c$ is stored in a finite-capacity battery (the lossy path). The transmitter combines direct power with battery discharge power $d$ to drive data transmission, while also accounting for a fixed circuit power $p$.
Efficiency Modeling
To capture the impact of internal resistance, the paper develops non-linear efficiency models for both charging and discharging cycles. By analyzing equivalent circuits—a voltage source in series with a resistor—the authors derive tractable models where efficiency decreases as the power rate increases.
As illustrated in Figure 4, higher internal resistance ($r_2 > r_1$) leads to a steeper decline in efficiency as charging power ($c_p$) or discharging power ($d_p$) increases. This rate-dependency is a critical departure from ideal models and necessitates new optimization policies.
Optimization Policies
The paper addresses the optimization of the Time-Splitting Ratio (TSR) and Power-Splitting Ratio (PSR) to maximize the communication rate:
- Off-line Optimization: Assuming future energy arrivals are known, an iterative algorithm solves the resulting non-convex problem to find a theoretical upper bound.
- On-line Policies: For real-world use where the future is unknown, the authors use Stochastic Dynamic Programming (SDP) to find the optimal policy and propose three practical heuristics:
- Greedy: Uses all available energy in the current frame.
- Statistical Algorithm (SA): Uses mean values of future arrivals to make decisions.
- Constant Splitting: Uses a pre-computed, fixed ratio regardless of fluctuations.
Key Insights and Results
- The Death of the "Double Threshold": In ideal models, optimal transmit power stays constant over certain ranges. With internal resistance, this disappears; optimal transmit power becomes strictly monotonic to balance rising internal losses as harvested power increases.
- Dedicated Charging Phases: The authors prove it is often optimal to have a period where the device only charges and does not transmit, minimizing circuit power waste during weak energy arrivals.
- Direct Path Preference: When harvested power is high, the system prioritizes the direct path to avoid the significant $I^2r$ heat losses associated with cycling high power through the battery.
- Performance: Simulations show that charging efficiency can vary by up to 15% and discharging by up to 30% depending on the power rate. The proposed Statistical Algorithm (SA) performs remarkably well, achieving results very close to the optimal SDP policy.
Conclusion
Battery internal resistance significantly impacts the design and performance of energy harvesting communication systems. Policies designed for "ideal" batteries perform poorly in real simulations because they over-use the battery, leading to excessive resistive losses. By incorporating rate-dependent efficiency models, this research provides a more realistic framework for designing efficient, self-powered communication systems.
Summary updated