Effect of Modifiers on the Performance of Polypropylene/Calcium Carbonate Composites

Deqin Zhu, Yu Sheng, Yinjiang Zou, Zhen Fang, Su Xiao-fenChinese 2013 · DOI

Abstract

This study explores an in-situ solid-phase grafting modification method to enhance the performance of polypropylene (PP)/calcium carbonate ($CaCO_3$) composites. By using maleic anhydride (MAH) as a chemical bridge and polypropylene wax (PPW) as a coating, researchers developed $CaCO_3$-MAH-PPW core-shell particles. Compared to traditional compatibilization using PP-g-MAH, this novel approach significantly improves impact toughness, flexural strength, and melt processability. The optimal performance was observed at a filler content of 20 phr, where the notched impact strength increased by 19% over pure PP.

Introduction

Polypropylene (PP) is widely utilized in industrial applications due to its cost-effectiveness and versatile properties. To enhance stiffness and reduce material costs, inorganic fillers like $CaCO_3$ are commonly incorporated. However, the inherent incompatibility between non-polar PP and polar $CaCO_3$ often leads to poor interfacial adhesion, resulting in reduced toughness and poor particle dispersion. While traditional compatibilizers like maleic anhydride-grafted polypropylene (PP-g-MAH) offer some improvement, they often reach a plateau in effectiveness. This research investigates a "pre-packaging" strategy where $CaCO_3$ particles are chemically modified with a polymer shell prior to blending.

Experimental Methods

The core of this research is the In-situ Solid-Phase Grafting technique. In the first stage, $CaCO_3$ is reacted with MAH at 100°C, allowing the MAH to anchor to the inorganic surface. Subsequently, polypropylene wax (PPW) and an initiator (BPO) are introduced at 120°C, triggering the grafting of PPW onto the MAH "bridge." This process creates a $CaCO_3$-MAH-PPW composite particle.

To verify the success of this chemical modification, Fourier Transform Infrared (FTIR) spectroscopy was employed. As shown in the spectra below, the emergence of specific absorption peaks confirms the presence of the MAH-PPW layer on the $CaCO_3$ surface.

FTIR spectra confirming the chemical grafting of MAH and PPW onto the CaCO3 surface.

The performance of these modified composites was compared against a control group using standard $CaCO_3$ and a commercial PP-g-MAH compatibilizer. Mechanical properties were evaluated through notched impact, tensile, and flexural testing across a range of filler loadings (0–40 phr).

Results and Discussion

The mechanical performance of the composites is highly dependent on the filler loading and the modification method. The in-situ modified composites consistently outperformed the traditional blends in terms of impact and flexural strength at higher loadings.

Mechanical properties of PP/CaCO3 composites: (A) Notched impact strength, (B) Flexural strength, and (C) Tensile strength. Curve 'a' represents the in-situ modified CaCO3-MAH-PPW composite.

Impact Toughness and Interfacial Bonding

The notched impact strength (Figure A above) reached its peak at 20 phr for the in-situ modified material, achieving a value 1.19 times that of pure PP. This enhancement is attributed to the "moderate" bonding provided by the MAH-PPW shell. Under stress, these particles can undergo controlled debonding, creating micro-voids that trigger matrix shear yielding. This mechanism effectively absorbs energy and prevents catastrophic crack propagation.

Flexural and Tensile Performance

While tensile strength generally decreases with filler content due to the reduction in the effective cross-section of the polymer matrix (Figure C), the flexural strength (Figure B) showed a significant recovery and eventual increase for the in-situ modified composites at higher loadings. This indicates that the modified interface effectively transfers stress between the filler and the matrix.

Enhanced Processability

A notable advantage of the in-situ method is the dramatic improvement in melt flow. The PPW coating acts as an internal lubricant, reducing friction and chain entanglement. The Melt Flow Rate (MFR) of the in-situ modified material was found to be up to 2.38 times higher than that of the traditional PP-g-MAH version, facilitating easier and faster manufacturing.

Conclusion

The in-situ solid-phase grafting of $CaCO_3$ with MAH and PPW offers a superior alternative to traditional compatibilization methods for PP composites. By creating a tailored interfacial layer, this technique simultaneously improves toughness, stiffness, and processability. While the multi-step preparation process presents some industrial complexity, the significant performance gains—particularly the 19% boost in impact strength and doubled flow rate—make it a promising approach for high-performance polypropylene applications.

Summary updated

Abstract

摘要: 以马来酸酐(MAH)、聚丙烯蜡(PPW)为主要原料,采用原位固相接枝改性法制得PP/CaCO3-MAH-PPW复合材料,并与添加相容剂聚丙烯接枝马来酸酐(PP-g-MAH)所制得的PP/PP-g-MAH/CaCO3复合材料进行比较。 结果表明,CaCO3良好的分散性及其与PP基体适宜的界面粘接是复合材料具有较好韧性的关键因素。 与PP/PP-g-MAH/CaCO3复合材料相比,PP/CaCO3-MAH-PPW复合材料表现出更佳的冲击、弯曲和加工性能,当m(PP)∶m(CaCO3)=100∶20时,材料缺口冲击强度达到最大值,是基体树脂的1.19倍。
BibTeX
@inproceedings{zhu2013effect,
  author = {Deqin Zhu and Yu SHENG and Yinjiang ZOU and Zhen Fang and SU Xiao-fen},
  title = {{Effect of Modifiers on the Performance of Polypropylene/Calcium Carbonate Composites}},
  booktitle = {Chinese},
  year = {2013},
  doi = {10.3724/sp.j.1095.2013.20504},
}
Figure