Combustion characteristics of cattle manure and pulverized coal co-firing under oxy-fuel atmosphere in non-isothermal and isothermal conditions

Yao Zhu, Baojun Yi, Qiaoxia Yuan, Hongliang Cao, Shuiping YanBioResources 2018 · DOI

Abstract

This study investigates the combustion characteristics of cattle manure (CM) and pulverized coal blends under an oxy-fuel ($O_2/CO_2$) atmosphere. Factors such as furnace temperature, $O_2$ concentration, and blending ratio were analyzed under both non-isothermal and isothermal conditions. Results indicate that blending CM improves the combustion characteristics of pulverized coal, particularly by lowering ignition temperatures. However, the blending ratio significantly impacts the process, with ratios exceeding 50% drastically altering the combustion profile. The interaction between CM and coal was found to be consistent across both heating regimes, providing critical data for optimizing waste-to-energy processes in carbon-capture-ready environments.

Introduction

The rapid expansion of the cattle industry has led to a surplus of manure that exceeds natural environmental processing capacities. While combustion offers a path for waste reduction and energy recovery, cattle manure (CM) is a challenging fuel due to its high moisture and ash content. Co-firing CM with coal under oxy-fuel conditions—where air is replaced by $O_2/CO_2$—presents a dual benefit: sustainable waste management and facilitated carbon capture. This research explores the synergy between CM and two types of coal: Shanxi bituminous (SX) and Xiaolongtan lignite (XLT).

Methodology

The researchers employed Thermogravimetric Analysis (TGA) to evaluate combustion kinetics under two regimes:

  1. Non-isothermal: Samples were heated from room temperature to 800°C at 20°C/min to identify stages of dehydration, volatile release, and char oxidation.
  2. Isothermal: Samples were rapidly introduced into a pre-heated furnace (500°C to 900°C) to simulate industrial "thermal shock."

Blends ranged from 10% to 90% CM. Kinetic parameters were calculated using the Coats-Redfern integral method to determine apparent activation energy ($E$).

Non-Isothermal Combustion Analysis

The non-isothermal tests revealed that CM acts as a "volatile boost." Because CM has a higher volatile content (45.8%) compared to coal, it ignites earlier, providing a pilot flame that accelerates the ignition of coal particles.

TG and DTG curves for CM/SX and CM/XLT blends under non-isothermal conditions.

As shown in Figure 4, adding CM consistently shifts the TG curves to lower temperatures, reducing both ignition ($T_{ig}$) and burnout ($T_b$) temperatures. The impact is more pronounced for bituminous coal (SX) than for lignite (XLT), as CM's combustion profile is naturally closer to that of lignite.

Isothermal Combustion and Temperature Effects

Isothermal experiments provided insight into how furnace temperature affects reaction intensity. At lower temperatures (e.g., 500°C), combustion was found to be sluggish and incomplete.

TG and DTG curves under isothermal conditions at various furnace temperatures.

Figure 6 demonstrates that increasing the furnace temperature to 700°C or higher significantly enhances the reaction rate, as evidenced by the sharper DTG peaks and faster mass loss. This suggests that industrial boilers must maintain a high enough temperature to handle the specific kinetics of biomass-coal blends effectively.

Key Insights: The 30% Blending Rule

A critical finding is the "30% rule." While CM improves ignition, blending ratios above 30% can destabilize the combustion process in boilers designed for coal. When the CM ratio exceeds 50%, the activation energy of the blend drops to levels similar to pure manure, and the combustion profile shifts entirely, requiring higher $O_2$ concentrations (up to 40%) to maintain efficiency.

Conclusion

Co-firing cattle manure with coal in an oxy-fuel atmosphere is a viable strategy for energy recovery and waste management. While CM improves the ignition characteristics of coal, careful management of the blending ratio is essential to avoid process instability. Future work should address the large-scale implications of ash chemistry, specifically the role of alkali metals in boiler fouling and corrosion.

Summary updated

Abstract

Combustion characteristics of cattle manure (CM) and pulverized coal blends under oxy-fuel atmosphere were considered. Factors such as the furnace temperature, O2 concentration, and blending ratio were analyzed. The experiment under non-isothermal and isothermal conditions were used to study effects of the heating rate. Blended CM can improve the combustion characteristics of pulverized coal. However, a difference exists between the increase of the blending ratio of CM with Shanxi bituminous coal (SX) and Xiaolongtan lignite coal (XLT) under various O2 concentration conditions. More attention should be paid to the blending ratio > 50%. CM and coal co-firing affected by the furnace temperature had a close association with its characteristics. Inhibition was found in most conditions, and the trend of interaction between CM and coal under the non-isothermal and isothermal condition was consistent. These experiments provided information for the utilization of livestock and poultry manure and pulverized coal blends in the oxy-fuel atmosphere.
BibTeX
@inproceedings{zhu2018combustion,
  author = {Yao Zhu and Baojun Yi and Qiaoxia Yuan and Hongliang Cao and Shuiping Yan},
  title = {{Combustion characteristics of cattle manure and pulverized coal co-firing under oxy-fuel atmosphere in non-isothermal and isothermal conditions}},
  booktitle = {BioResources},
  year = {2018},
  doi = {10.15376/biores.13.3.6465-6479},
}
Figure