Anchoring of Turbulent Premixed Hydrogen/Air Flames at Externally Heated Walls

Sebastian Klukas, Moritz Sieber, M. Giglmaier, Sebastian Schimek, Christian Oliver Paschereit, Nikolaus A. Adams

Abstract

A joint experimental and numerical investigation of turbulent flame front anchoring at externally heated walls is presented. The phenomenon is examined for lean hydrogen/air mixtures in a novel burner design, which comprises a cylindrical burning chamber converging into a glass pipe as well as a wall heating assembly at their intersection. The transparent part allows for optical OH* chemiluminescence measurements serving as a basis for numerical validation. For a comprehensive numerical evaluation the effect of heat loss on different hydrogen/air chemical reaction mechanisms is reviewed in a preparatory one-dimensional flame study. The subsequent numerical investigation focuses on the application of the Eddy Dissipation Concept (EDC) as a turbulence-chemistry interaction model in the realm of wall anchoring turbulent flames. All simulations are based on the Reynolds time-averaged formulation of the Navier-Stokes equations and feature axisymmetric domains. The influence of different two-equation turbulence models and EDC modeling constants are discussed. Since wall heat transfer is responsible for ignition as well as quenching of the flame front, a special focus is put on boundary layer resolving near-wall treatment. A qualitative comparison between simulations and experiment is performed for multiple operating conditions. These are selected to display the influence of equivalence ratio, bulk Reynolds number and unburnt mixture temperature. While the choice of RANS-based turbulence model has a distinguishable impact, EDC modeling coefficients exhibit a more significant influence on flame shape and length. It is only surpassed by the impact of correct diffusion treatment on reacting lean hydrogen/air mixtures. To depict this behavior as accurately as possible, full multicomponent diffusion treatment using the Maxwell-Stefan equation is applied.

Introduction

Stable flame anchoring is a fundamental challenge for continuous combustion devices such as jet engines, scramjets, and micro-combustors. Traditional stabilization methods often rely on recirculation zones created by bluff bodies or cavities, which can introduce significant pressure losses. Hydrogen offers a clean alternative fuel but presents a paradox: despite its high flame speeds, it is notoriously difficult to stabilize in ultra-lean mixtures. This research explores excess enthalpy combustion, where heat from burnt gases is conducted back through burner walls to preheat the incoming mixture, enabling stable anchoring in high-velocity, low-fuel environments.

Experimental and Numerical Methodology

The study utilizes a dual approach combining a novel experimental burner with refined Computational Fluid Dynamics (CFD) modeling. The burner features a cylindrical chamber converging into a transparent quartz glass pipe, allowing for $OH^*$ chemiluminescence measurements to map the reaction zone.

The experimental burner setup includes (a) fuel injection details, (f) the heating assembly with a quartz tube for optical access, and (a-h) the full longitudinal assembly with dimensions in mm.

Numerical simulations were performed using Reynolds-Averaged Navier-Stokes (RANS) formulations in Ansys Fluent. Key modeling choices included:

  • Turbulence-Chemistry Interaction: The Eddy Dissipation Concept (EDC) was employed to model reaction rates within turbulent flows.
  • Chemical Kinetics: The Li mechanism (10 species, 29 reactions) was selected following a 1D sensitivity study for its superior accuracy in capturing heat loss effects.
  • Diffusion Modeling: Given the high mobility of hydrogen, full multicomponent diffusion was implemented using the Maxwell-Stefan equations.
  • Near-Wall Treatment: A boundary-layer-resolving mesh ($y^+ \approx 1$) was used to capture the delicate balance between wall-induced ignition and quenching.

Operating Conditions and Datasets

The performance of the anchoring mechanism was evaluated across six distinct operating cases. These cases varied the equivalence ratio ($\Phi$), bulk Reynolds number ($Re$), and unburnt mixture temperature ($T_u$) to provide a comprehensive benchmark for the numerical models.

Table of operating conditions for the six cases investigated, detailing mass flow, temperature, equivalence ratio, and dimensionless numbers.

Key Insights and Results

The Necessity of EDC Tuning

The researchers found that standard EDC modeling constants ($C_\gamma$) were insufficient for wall-anchored flames. Adjusting $C_\gamma$ from the default 2.1366 to 3.0 significantly improved the alignment between simulated flame shapes and experimental $OH^*$ data.

Impact of Diffusion and Wall Interaction

For lean hydrogen mixtures, the implementation of Maxwell-Stefan multicomponent diffusion proved more critical than the choice of turbulence model. The heated wall serves a dual purpose: it acts as a thermal trigger to ignite the mixture upstream, while the wall surface itself eventually quenches the flame (Side Wall Quenching), creating a stable anchoring point just downstream of the heating ring.

Flame Morphology

The simulations successfully captured the characteristic "V-shape" of anchored flames. Results indicated that increasing the equivalence ratio ($\Phi$) from 0.2 to 0.3 significantly shortened the flame due to increased flame speeds. Conversely, lowering the unburnt mixture temperature ($T_u$) resulted in more elongated flames, a trend accurately predicted by the tuned EDC model.

Conclusion

This study demonstrates that a tuned RANS-based EDC model, combined with multicomponent diffusion, provides a robust framework for designing hydrogen combustion systems utilizing heated wall anchoring. While the axisymmetric RANS approach is computationally efficient for engineering design, future work involving Large Eddy Simulation (LES) may be required to resolve transient instabilities and 3D effects in non-vertical or larger-scale installations.

Summary updated

Abstract

A joint experimental and numerical investigation of turbulent flame front anchoring at externally heated walls is presented. The phenomenon is examined for lean hydrogen/air mixtures in a novel burner design, which comprises a cylindrical burning chamber converging into a glass pipe as well as a wall heating assembly at their intersection. The transparent part allows for optical OH* chemiluminescence measurements serving as a basis for numerical validation. For a comprehensive numerical evaluation the effect of heat loss on different hydrogen/air chemical reaction mechanisms is reviewed in a preparatory one-dimensional flame study. The subsequent numerical investigation focuses on the application of the Eddy Dissipation Concept (EDC) as a turbulence-chemistry interaction model in the realm of wall anchoring turbulent flames. All simulations are based on the Reynolds time-averaged formulation of the Navier-Stokes equations and feature axisymmetric domains. The influence of different two-equation turbulence models and EDC modeling constants are discussed. Since wall heat transfer is responsible for ignition as well as quenching of the flame front, a special focus is put on boundary layer resolving near-wall treatment. A qualitative comparison between simulations and experiment is performed for multiple operating conditions. These are selected to display the influence of equivalence ratio, bulk Reynolds number and unburnt mixture temperature. While the choice of RANS-based turbulence model has a distinguishable impact, EDC modeling coefficients exhibit a more significant influence on flame shape and length. It is only surpassed by the impact of correct diffusion treatment on reacting lean hydrogen/air mixtures. To depict this behavior as accurately as possible, full multicomponent diffusion treatment using the Maxwell-Stefan equation is applied.
BibTeX
@article{klukas2020anchoring,
  author = {Sebastian Klukas and Moritz Sieber and M. Giglmaier and Sebastian Schimek and Christian Oliver Paschereit and Nikolaus A. Adams},
  title = {{Anchoring of Turbulent Premixed Hydrogen/Air Flames at Externally Heated Walls}},
  journal = {International Journal of Hydrogen Energy},
  year = {2020},
  doi = {10.1016/j.ijhydene.2020.08.201},
}

Loading related content...

Figure