An Implantable Piezofilm Middle Ear Microphone: Performance in Human Cadaveric Temporal Bones

John Z. Zhang, Lukas Graf, Annesya Banerjee, Aaron Yeiser, Christopher I. McHugh, Ioannis Kymissis, Jeffrey H. Lang, Elizabeth S. Olson, Hideko Heidi Nakajima

Abstract: One of the major reasons that totally implantable cochlear microphones are not readily available is the lack of good implantable microphones. An implantable microphone has the potential to provide a range of benefits over external microphones for cochlear implant users including the filtering ability of the outer ear, cosmetics, and usability in all situations. This paper presents results from experiments in human cadaveric ears of a piezofilm microphone concept under development as a possible component of a future implantable microphone system for use with cochlear implants. This microphone is referred to here as a drum microphone (DrumMic) that senses the robust and predictable motion of the umbo, the tip of the malleus. The performance was measured of five DrumMics inserted in four different human cadaveric temporal bones. Sensitivity, linearity, bandwidth, and equivalent input noise were measured during these experiments using a sound stimulus and measurement setup. The results demonstrate that the DrumMic behaves robustly across ears and fabrication, with performance approaching that of commercial hearing aid microphones.

Introduction

Cochlear implants (CIs) have revolutionized hearing for over a million people, yet they remain dependent on external hardware. External microphones are aesthetically conspicuous, susceptible to wind noise, and unusable in water or during sleep. Perhaps most importantly, they bypass the natural "pinna effect"—the way the outer ear and ear canal naturally filter and amplify sound to provide cues for localization and speech clarity.

The "holy grail" of CI research is a totally implantable system. However, the primary bottleneck has been the microphone. Subcutaneous sensors often suffer from poor signal-to-noise ratios due to skin attenuation. This study explores a middle-ear approach using a "DrumMic" designed to sense the mechanical vibrations of the ossicular chain directly.

Methodology and Design

The DrumMic concept is based on a piezoelectric polymer called polyvinylidene fluoride (PVDF). The device consists of a thin PVDF membrane stretched over a 3mm brass ring.

The DrumMic prototype, showing the PVDF membrane and brass ring assembly alongside scale measurements.

As sound vibrates the eardrum and the ossicular chain, the umbo (the tip of the malleus bone) moves, stretching the PVDF membrane. This mechanical strain generates an electrical charge processed by a custom low-noise charge amplifier.

The researchers tested five custom-fabricated DrumMics across four human cadaveric temporal bones. To ensure optimal mechanical contact, tiny plastic shims (0.65 mm thick) were used to tension the microphone between the cochlear promontory and the umbo. Laser Doppler Vibrometry (LDV) was used to measure the actual velocity of the umbo to benchmark the microphone's electrical output.

Key Results

Experimental testing demonstrated that the DrumMic provides a robust and predictable signal:

  • Linearity: The device behaved linearly across a massive dynamic range, from 46 dB SPL to at least 100 dB SPL.
  • Bandwidth: It maintained a strong signal-to-noise ratio up to 8 kHz, covering the essential frequencies for human speech.
  • Sensitivity: The output was tightly clustered around 25 fC/Pa across different ears and devices, despite anatomical variations.
  • Noise Floor: The measured Equivalent Input Noise (EIN) was 54 dB SPL. However, when accounting for the natural 10–20 dB pressure gain provided by the ear canal and pinna, the effective EIN was estimated at 46 dB SPL.
Surgical placement of the DrumMic in a cadaveric ear (left) and a schematic cross-section (right) showing its position between the umbo and cochlear promontory.

Discussion

A critical finding of this study is the "canceling effect" that makes the DrumMic robust to surgical placement. While a tighter fit (using more shims) increases the tension and sensitivity of the PVDF film, it also stiffens the ear's mechanics, which reduces the umbo's motion. These two factors effectively balance each other, resulting in consistent performance across different anatomical structures.

Furthermore, by placing the sensor behind the eardrum, the system leverages the natural anatomy of the ear. The pressure gain from the ear canal helps offset the intrinsic noise of the sensor, bringing its performance closer to the ~34 dB SPL floor of top-tier external hearing aid microphones.

Conclusion and Future Work

The DrumMic demonstrates linear, wide-bandwidth performance that is remarkably stable across different subjects. To transition this concept into a human-implantable prototype, future research must focus on hermetic encapsulation to protect the device from the moist environment of the middle ear, biocompatibility, and long-term mechanical stability. Additionally, further optimization of the charge amplifier and electrical shielding will be necessary to further reduce the noise floor.

Summary updated

Abstract

Purpose: One of the major reasons that totally implantable cochlear microphones are not readily available is the lack of good implantable microphones. An implantable microphone has the potential to provide a range of benefits over external microphones for cochlear implant users including the filtering ability of the outer ear, cosmetics, and usability in all situations. This paper presents results from experiments in human cadaveric ears of a piezofilm microphone concept under development as a possible component of a future implantable microphone system for use with cochlear implants. This microphone is referred to here as a drum microphone (DrumMic) that senses the robust and predictable motion of the umbo, the tip of the malleus. Methods: The performance was measured of five DrumMics inserted in four different human cadaveric temporal bones. Sensitivity, linearity, bandwidth, and equivalent input noise were measured during these experiments using a sound stimulus and measurement setup. Results: The sensitivity of the DrumMics was found to be tightly clustered across different microphones and ears despite differences in umbo and middle ear anatomy. The DrumMics were shown to behave linearly across a large dynamic range (46 dB SPL to 100 dB SPL) across a wide bandwidth (100 Hz to 8 kHz). The equivalent input noise (0.1-10 kHz) of the DrumMic and amplifier referenced to the ear canal was measured to be 54 dB SPL and estimated to be 46 dB SPL after accounting for the pressure gain of the outer ear. Conclusion: The results demonstrate that the DrumMic behaves robustly across ears and fabrication. The equivalent input noise performance was shown to approach that of commercial hearing aid microphones. To advance this demonstration of the DrumMic concept to a future prototype implantable in humans, work on encapsulation, biocompatibility, connectorization will be required.
BibTeX
@article{zhang2024implantable,
  author = {John Z. Zhang and Lukas Graf and Annesya Banerjee and Aaron Yeiser and Christopher I. McHugh and Ioannis Kymissis and Jeffrey H. Lang and Elizabeth S. Olson and Hideko Heidi Nakajima},
  title = {{An Implantable Piezofilm Middle Ear Microphone: Performance in Human Cadaveric Temporal Bones}},
  journal = {Journal of the Association for Research in Otolaryngology},
  year = {2024},
  doi = {10.1007/s10162-024-00927-4},
}
Figure