Abstract
Noise pollution has attracted a wide attention due to its negative effect on human health, and many researchers are working on proposing strategies or developing new materials to improve acoustic performance of structures and building materials. Meanwhile, the worldwide emphasis on sustainable development has motivated the development and application of bio-mass materials in every field, including the engineering construction. The purpose of this study is to measure and investigate the performance of a structure-used glued laminated bamboo (Glubam) and spruce-pine-fir (SPF) as soundproof or sound-absorbing materials. The impedance tube method was used to measure the sound reduction index and sound absorption coefficient of glubam and SPF in the lab. After doing some comparison studies, it can be found that glubam and SPF have good performance in sound insulation but behave weakly in sound absorption, and glubam exhibits similar even better acoustic properties than SPF. Moreover, a finite element model was built up using ABAQUS to predict sound insulation properties of materials. According to the numerical results of sound reduction index obtained from the finite element model, developing composite materials and double-layer panels with cavity between should be effective on improving the soundproof performance of SPF and glubam.
Introduction
As the construction industry shifts toward sustainable "green" practices, there is a growing demand for bio-mass materials to replace carbon-intensive steel and concrete. While structural integrity is paramount, these materials must also address environmental factors like noise pollution. Timber, specifically Spruce-Pine-Fir (SPF), is a traditional choice, but bamboo-based products like Glubam are emerging as high-strength, fast-growing alternatives. This study investigates the acoustic properties—specifically sound insulation and absorption—of different types of Glubam compared to traditional SPF timber.
Materials and Experimental Methods
The research evaluated three distinct bio-mass materials: thin-strip Glubam, thick-strip Glubam, and SPF timber. Thin-strip Glubam consists of 2mm thick bamboo strip mats laminated bidirectionally, while thick-strip Glubam uses 5–8mm thick bamboo strips pressure-glued together.
The acoustic performance was measured using impedance tube methods following ISO and ASTM standards. A two-microphone setup was used for sound absorption coefficients ($\alpha$), while a four-microphone setup measured the sound reduction index ($TL$).
To account for the materials' anisotropic nature, specimens were tested in three orthogonal directions ($x, y, z$). Additionally, the effect of moisture content was examined by comparing "absolutely dry" specimens with those in a "natural environment." Numerical simulations were also performed using a finite element model (FEM) in ABAQUS to predict insulation properties and explore structural optimizations.
Results and Discussion
Anisotropy and Sound Transmission
A key finding was that acoustic properties vary significantly based on grain direction. Sound insulation was weakest along the $x$-axis (the grain/strip direction). This is attributed to microscopic structures like tracheids in wood or manufacturing voids in thin-strip Glubam, which act as channels for sound waves.
Insulation vs. Absorption Trade-off
The materials exhibited a classic inverse relationship: factors improving sound insulation (like higher density or moisture) typically decreased sound absorption. Thick-strip Glubam demonstrated the best overall sound insulation performance across both low and high-frequency ranges, outperforming both thin-strip Glubam and SPF.
Frequency Effects and Optimization
All materials showed a significant drop in soundproofing around 2000Hz due to the "coincidence effect," where the sound wavelength in the air matches the structural bending waves in the material. While all three materials were found to be "weak" absorbers compared to dedicated acoustic materials like glass wool, SPF showed slightly higher absorption at high frequencies.
The ABAQUS model demonstrated that simply increasing material thickness provides diminishing returns. Instead, developing composite materials or double-layer panels with an internal air cavity significantly boosts soundproofing performance.
Conclusion
Glubam and SPF are effective sound insulators but poor sound absorbers. Thick-strip Glubam, in particular, shows promise as a superior sustainable alternative to traditional timber for soundproofing applications. To optimize performance, the study suggests using double-layer panels with an internal air cavity or composite "sandwich" structures. Future work should focus on full-scale wall and floor assembly testing to validate these findings in real-world architectural settings.
Summary updated