Acid Leaching Tests on a Highly Oxidized Copper Ore in Yunnan

Yang Zhao, Siqing Liu, Dan Wang, Hailin Liu, Tingting Li2015 · DOI

Abstract: This study investigates the extraction of copper from highly oxidized ore in Yunnan Province using sulfuric acid solutions. Experimental results demonstrate that copper leaching rates can exceed 90% under optimized conditions: a particle size of -1mm, a leaching time of 3 hours, a liquid-to-solid weight ratio of 4:1, and an ore-to-sulfuric acid weight ratio of 1:0.4 at ambient temperature and pressure.

Introduction

As global copper demand escalates, the metallurgical industry is shifting focus toward "refractory" oxidized and mixed ores. These ores typically present lower grades and complex mineralogies that render traditional extraction methods inefficient. The specific ore studied from Yunnan Province exhibits an exceptionally high oxidation rate of 86.36%. While acid leaching is a standard approach, identifying the optimal parameters—balancing recovery rates against chemical consumption and processing costs—remains a critical engineering challenge.

Experimental Methodology

Laboratory-scale tests were conducted using a ZHWY-100B biological shaking table to simulate the leaching process at normal temperature (25°C) and pressure. The study systematically evaluated four primary variables:

  1. Grinding Fineness: Assessing the necessity of fine crushing.
  2. Leaching Time: Identifying the kinetic plateau for extraction.
  3. Liquid-Solid Ratio: Optimizing solvent volume relative to ore mass.
  4. Ore-to-Acid Ratio: Determining the ideal concentration of sulfuric acid.

The ore sample was characterized by a copper grade of approximately 2.42%, primarily composed of malachite, azurite, and cuprite, with associated minerals such as kaolin and goethite.

Results and Discussion

The "Grinding Myth"

A significant finding of this research is that intensive grinding is largely unnecessary for this specific ore type. Increasing the grinding fineness from 20% to 80% (measured by -0.074mm occupancy) only improved the leaching rate by a marginal 1.3%. Given that grinding is one of the most energy-intensive and costly stages of mineral processing, utilizing a simpler -1mm crushing process significantly enhances the economic viability of the operation.

Leaching Kinetics

The leaching process exhibits rapid initial kinetics. As illustrated in the experimental data, the majority of copper recovery occurs within the first three hours. Extending the duration to four hours yielded only a negligible 0.37% increase in recovery, suggesting that a 3-hour cycle is the most efficient duration for industrial application.

Figure 3: Effect of leaching time on the copper recovery rate, showing a plateau after 3 hours.

Chemical Optimization

The study revealed a distinct "peak of efficiency" regarding acid consumption. Increasing the ore-to-sulfuric acid ratio beyond 1:0.4 resulted in a decrease in the leaching rate. This suggests that excessive acidity may interfere with the chemical equilibrium or physical contact required for optimal leaching, or perhaps lead to the dissolution of undesirable gangue minerals that consume acid without benefiting copper recovery.

Figure 4: Impact of the ore-to-sulfuric acid ratio on leaching efficiency, highlighting the 1:0.4 optimum.

Conclusion

The optimized process achieved a consistent copper leaching rate of over 90% (averaging 91%). The resulting leachate was of high quality, containing 91.79% copper with manageable levels of impurities such as Iron (5.64%) and Zinc (2.31%). By avoiding unnecessary fine grinding and optimizing chemical ratios, this method provides a low-cost, effective pathway for processing high-oxidation copper ores in the Yunnan region. Future work should focus on scaling these results to industrial heap or vat leaching environments and addressing the environmental management of acidic tailings.

Summary updated

Abstract

The extraction of copper from highly oxidized copper ore in sulfuric acid solutions was examined in Yunnan Province. During the leaching of copper, the leaching rate of cuprous concentration was affected by various parameters such as particle size, leaching time, the weight ratio of liquid to solid and the consumption of sulfuric acid, etc. Through a series of tests, the results show that leaching rate of copper reaches more than 90% by means of sulfuric acid under the best conditions which are particle size of -1mm, the leaching time of 3h, the liquid-solid weight ratio of 4:1, the weight ratio of ore to sulfuric acid of 1:0.4 at normal temperature and pressure
BibTeX
@misc{zhao2015acid,
  author = {Yang Zhao and Siqing Liu and Dan Wang and Hailin Liu and Tingting Li},
  title = {{Acid Leaching Tests on a Highly Oxidized Copper Ore in Yunnan}},
  year = {2015},
  doi = {10.2991/meic-15.2015.327},
}
Figure