A Novel Floating High-Voltage Level Shifter with Pre-Storage Technique

Qiang Li, Yuan Yang, Haohao Ma, Yangle Zhou, Guolong You, Minmin Zhang, Wei Xiang

TL;DR

This paper introduces a novel Floating High-Voltage Level Shifter (FHV-LS) that achieves sub-nanosecond propagation delays by optimizing transmission paths with a "pre-storage" technique. Further improvements include a "regulated strength" pull-up network and a "pseudosymmetrical" input pair to reduce delay and improve symmetry, along with a start-up circuit for reliable initialization.

What Problem Does This Paper Address?

Modern power electronics, especially in gate drivers, demand increasingly faster switching speeds and higher operating frequencies. This necessitates gate drivers with very low propagation delays to ensure accurate feedback-based regulation and rapid fault protection. Existing level-shifting circuits, crucial for interfacing different voltage domains within these drivers, often suffer from significant propagation delays (on the order of nanoseconds) and asymmetry between rising and falling signal transitions. These issues can lead to distorted duty cycles and limit the overall performance of high-speed power systems. The paper aims to tackle these limitations by developing an FHV-LS that is both faster and more symmetrical.

Methods

The core innovation is the pre-storage technique. Instead of directly transmitting the input signal through a series of gates, the proposed FHV-LS first stores the input state in a register (pre-Reg). When the input signal changes, this stored state is then transferred to the output. This approach optimizes the signal transmission path, effectively reducing the number of delay elements and achieving sub-nanosecond propagation delays.

To further enhance performance, two key improvements are introduced:

  • Pull-up network with regulated strength: This technique addresses the "fall time" of the output signal, which is a critical component of the overall propagation delay. By employing a carefully designed pull-up network, the authors increase the pull-up resistance, which paradoxically helps to reduce the fall time by optimizing the discharge of parasitic capacitances.
  • Pseudosymmetrical input pair: To minimize the difference between rising and falling propagation delays (improving symmetry), a pseudosymmetrical input structure replaces a conventional inverter. This design aims to balance the delay characteristics of both transitions.

Additionally, a start-up circuit is incorporated to ensure the output of the level shifter is initialized to a known state (low) during the high-voltage power-up sequence, preventing erroneous behavior.

The proposed FHV-LS is implemented using 0.3-µm HVCMOS technology.

Datasets

Not discussed in the paper. The evaluation relies on post-layout simulations and Monte Carlo simulations using the described HVCMOS technology.

Key Insights and Ideas

  • Pre-storage as a path optimization strategy: The paper demonstrates that re-architecting the signal path by introducing a register can be more effective for reducing propagation delay than simply optimizing individual gate delays. This highlights a higher-level design approach for speed optimization.
  • The critical role of fall time: The authors identify the fall time as a significant contributor to propagation delay and show how a seemingly counter-intuitive approach (increasing pull-up resistance) can actually reduce it by optimizing the discharge process.
  • Symmetry is key for high-speed applications: The paper emphasizes that not only low delay but also symmetry between rising and falling transitions is crucial to avoid duty cycle distortion, especially at high frequencies. The pseudosymmetrical input pair is a clever way to address this.
  • Start-up circuits are essential for robust power-up: The need for a dedicated start-up circuit to ensure predictable behavior during the VDDH power-up sequence underscores the practical challenges in high-voltage integrated circuit design.

Key Results

  • Sub-nanosecond propagation delay: The proposed FHV-LS achieves an average propagation delay of 384 ps at VH = 5 V.
  • Reduced energy per transition: The energy per transition (ET) is 77.7 pJ at VH = 5 V.
  • Improved symmetry: The deviation between rising and falling propagation delays is significantly reduced, with the paper noting a reduction from 36% to 20% after Improvement-II, and a difference of only 75 ps (attributed to body effect).
  • Stability: Monte Carlo simulations with 500 points show good stability against process variation and device mismatch, with normalized standard deviations of 0.015 for propagation delay and 0.016 for energy per transition.
  • Performance improvements: Improvement-I (regulated strength pull-up) reduced average propagation delay by 22%.

Limitations and Future Work

  • Operating Frequency: The paper notes that the rise time of VA/VB increases due to the regulated strength pull-up network, limiting the maximum operating frequency to approximately 100 MHz. While this is sufficient for many applications (e.g., IGBT and SiC power devices), it might be a limitation for extremely high-frequency scenarios.
  • dV/dt Immunity: The immunity to dV/dt of VSSH is reduced compared to the basic FHV-LS. The maximum immunity is stated as 5 V/ns.
  • Future Work: The authors suggest that the propagation delay and power consumption can be further optimized based on specific application requirements, implying that the presented design offers a tunable trade-off. The paper also implicitly suggests that further exploration of pseudosymmetrical structures and advanced pull-up network designs could yield even better results.

Summary updated

Abstract

This paper proposes a novel floating high-voltage level shifter (FHV-LS) with the pre-storage technique for high speed and low deviation in propagation delay. With this technology, the transmission paths from input to output are optimized, and thus the propagation delay of the proposed FHV-LS is reduced to as low as the sub-nanosecond scale. To further reduce the propagation delay, a pull-up network with regulated strength is introduced to reduce the fall time, which is a crucial part of the propagation delay. In addition, a pseudosymmetrical input pair is used to improve the symmetry of FHV-LS structurally to balance between the rising and falling propagation delays. Moreover, a start-up circuit is developed to initialize the output state of FHV-LS during the VDDH power up. The proposed FHV-LS is implemented using 0.3-µm HVCMOS technology. Post-layout simulation shows that the propagation delays and energy per transition of the proposed FHV-LS are 384 ps and 77.7 pJ @VH = 5 V, respectively. Finally, the 500-points Monte Carlo are performed to verify the performance and the stability.
BibTeX
@inproceedings{li2022novel,
  author = {Qiang Li and Yuan Yang and Haohao Ma and Yangle Zhou and Guolong You and Minmin Zhang and Wei Xiang},
  title = {{A Novel Floating High-Voltage Level Shifter with Pre-Storage Technique}},
  booktitle = {Sensors},
  year = {2022},
  url = {https://openreview.net/forum?id=whhL-hlsf7V},
}
Figure