Heat Transfer Performances and Exergetic Optimization for Solar Heat Receiver

Jianfeng Lu, Jing DingInTech 2011 · DOI · OpenAlex

Abstract

Solar energy is one kind of important resource for clean and renewable energy, and is widely investigated in many fields. In order to increase the operating temperature and thermodynamic efficiency, concentrated solar radiation is widely used to heat the working fluid in solar thermal power systems and other industrial engineering applications. Solar thermal power systems based on trough, dish, or heliostat fields are promising technologies due to their high operating temperatures. In these plants, the heat receiver is the critical component for photo-thermal transformation. This paper investigates the heat transfer performance of solar heat receivers, focusing on the three main contributions to heat loss: radiation, convection, and conduction. By developing a comprehensive numerical model, the study aims to optimize these receivers by balancing energy absorption with exergetic efficiency.

Introduction

In concentrated solar power (CSP) systems, the receiver is the "hot spot" where light is converted into thermal energy. As these systems are pushed to higher temperatures to improve engine efficiency, they inevitably lose more energy to the environment through radiation and convection. Most existing research focuses on either internal fluid dynamics or external heat losses in isolation. This paper bridges that gap by creating a coupled model that accounts for unilateral (one-sided) solar radiation. It specifically seeks to maximize exergetic efficiency—a Second Law of Thermodynamics approach that considers not just the quantity of heat collected, but its quality (temperature) for generating electricity.

Methodology

The authors developed a mathematical model of a straight-pipe receiver that integrates internal forced convection with external losses.

Schematic of heat transfer processes in a solar heat receiver pipe, illustrating incident solar energy, heat absorption, and losses via radiation, reflection, and natural convection.

Key components of the approach include:

  • Coupled Heat Transfer: Integration of equations for internal forced convection (using the Nusselt number correlation for turbulent flow) with external losses (natural convection and $T^4$ radiation).
  • Unilateral Radiation Modeling: Unlike models assuming uniform heating, this model accounts for the fact that solar concentrators hit only one side of the pipe, leading to significant circumferential temperature gradients.
  • Exergy Analysis: The study derived an exergetic efficiency formula to find the "sweet spot" where the fluid is hot enough to be useful but not so hot that heat losses become prohibitive.
  • Comparative Study: The model was tested using two fluids (Hitec molten salt and air) and two coatings (Co-Cd-BT with low emissivity and Pyromark with high emissivity).

Key Insights and Results

The Necessity of Selective Coatings

For air-based receivers, the choice of coating is a critical factor. Because air is a relatively poor heat conductor compared to molten salts, the pipe wall reaches much higher temperatures. Without a "selective" coating (high absorption, low infrared emission), radiation losses can cause efficiency to plummet.

Energy loss components and absorption efficiency for selective (Co-Cd-BT) vs. non-selective (Pyromark) coatings as a function of incident flux.

As shown in the energy balance analysis, the selective Co-Cd-BT coating significantly suppresses infrared radiation losses compared to the Pyromark coating. This allows air-based systems to reach a maximum efficiency of 64.2%, whereas standard high-emissivity coatings drop performance to approximately 30%.

Performance Benchmarks and Optimization

  • Molten Salt Performance: Reached a maximum local absorption efficiency of 92.46% at an optimal flux of 2.0 MW/m².
  • Optimal Flux Peak: Efficiency does not increase linearly with solar concentration. There is an optimal incident energy flux for every setup; beyond this point, radiation losses ($T^4$) outpace the gains from increased solar input.
  • Flow Velocity Impact: Increasing flow velocity for molten salt from 0.5 m/s to 2.0 m/s dropped the peak outlet wall temperature from 821.5 K to 574.0 K, significantly reducing thermal stress while increasing heat absorption.
  • Circumferential Averaging: The study found that while temperature varies wildly around the pipe (a 122K difference for molten salt), using the average incident flux to calculate overall efficiency results in a very small error (0.15% to 1.9%), justifying simpler 1D models for engineering estimates.

Conclusion

This research demonstrates that while molten salts are highly efficient, air-based systems can be significantly improved through exergetic optimization and advanced selective coatings. The findings suggest that future work should apply these methods to more complex 3D cavity geometries and multi-stage receiver designs to further enhance the viability of solar thermal power technology.

Summary updated

Abstract

Solar energy is one kind of important resource for clean and renewable energy, and is widely investigated in many fields. In order to increase the operating temperature and thermodynamic efficiency, concentrated solar radiation is widely used to heat the working fluid in solar thermal power system (Trieb & Nitsch, 1998) and other industrial engineerings (Klein et al., 2007; Ali et al., 2008). Concentrated solar radiation (Kalogirou, 2004) can be collected by the parabolic trough collector, parabolic dish reflector, heliostat field, etc. The concentrated energy flux has been studied in kinds of solar energy system. Moustafa et al. (1995) measured the solar flux density distribution on a plane receiver due to a flat heliostat. Estrada et al. (2007) proposed a calorimeter to measure the concentrated solar power produced by a point focus solar concentrator. Solar thermal power system based on trough, dish or heliostat field is a very promising and challenging technology for its high operating temperature and thermodynamic efficiency. In solar thermal power plant (Odeh et al., 2003), the heat transfer medium in solar heat receiver is heated by concentrated solar radiation to some high temperature, and then it can be used to operate kinds of heat engine and generate electricity. As a result, the heat receiver (Ortega et al., 2008) is the key problem for the photo-thermal transformation, and the heat transfer performance of solar heat receiver is the hotspot for solar energy research. The basic types of heat receiver in concentrated solar thermal system mainly include heat pipe receiver (Fujiwara et al., 1990), parabolic trough solar receiver (Gong et al., 2010), cavity receiver (Wu et al., 2010), and multistage solar receiver (Taragan, 1999), etc. The dynamical and thermal characteristics of solar heat receiver have been investigated in much literature (Cui et al., 2008; Grena, 2010). In general, the heat losses from solar receiver mainly include three contributions: radiation heat loss, convective heat loss, and conduction heat loss. The radiation heat loss (Melchior et al., 2008; Li et al., 2010) is mainly dependent upon the receiver structure, wall temperature, and emissivity/absorptivity of the receiver walls, while the convective heat loss (Clausing, 1981) is mainly determined by the receiver structure, wall temperature, and wind velocity. The heat conduction loss (Zavoico, 2001) exists in cavity receiver through the insulation wall, and it can be ignored in many solar heat receivers.
BibTeX
@inproceedings{lu2011heat,
  author = {Jianfeng Lu and Jing Ding},
  title = {{Heat Transfer Performances and Exergetic Optimization for Solar Heat Receiver}},
  booktitle = {InTech},
  year = {2011},
  doi = {10.5772/20135},
}
Figure