Uplink and Downlink Communications in Segmented Waveguide-Enabled Pinching-Antenna Systems (SWANs)

Chongjun Ouyang, Hao Jiang, Zhaolin Wang, Yuanwei Liu, Zhiguo Ding

TL;DR

This paper introduces Segmented Waveguide-Enabled Pinching-Antenna Systems (SWANs), a novel architecture that breaks down long dielectric waveguides into shorter, independent segments. By doing so, the authors solve the long-standing mathematical challenge of modeling uplink communications in these systems while simultaneously slashing signal attenuation and improving hardware maintainability.

What Problem Does This Paper Address?

The Pinching-Antenna SyStem (PASS), recently introduced by NTT DOCOMO, is a fascinating reconfigurable antenna technology. Imagine a "clothesline" (a dielectric waveguide) where you can snap on "clothespins" (dielectric particles called Pinching Antennas or PAs) anywhere you like to radiate or receive signals. It’s low-cost, flexible, and great for establishing line-of-sight links.

However, conventional PASS faces three major hurdles:

  1. The Uplink Modeling Nightmare: In a single long waveguide with multiple PAs, a signal captured by one PA can "re-radiate" out of another PA before it reaches the receiver. This Inter-Antenna Radiation (IAR) effect makes the math so complex that researchers previously couldn't create a tractable model for multi-antenna uplink.
  2. Propagation Loss: Dielectric waveguides aren't perfect; signals lose strength as they travel. In a very long waveguide, the "in-waveguide" loss becomes a performance killer.
  3. Maintainability: If a 100-meter waveguide breaks in the middle, you might have to replace the whole thing.

Methods

The authors propose SWAN, which replaces the single long waveguide with a series of short, independent segments, each with its own feed point connected to the Base Station.

To manage this new architecture, they define three operating protocols:

  • Segment Selection (SS): The simplest approach—only the segment closest to the user is activated.
  • Segment Aggregation (SA): All segments are connected to a single RF chain using a power splitter/combiner. This provides array gain but requires careful phase synchronization.
  • Segment Multiplexing (SM): The "gold standard"—each segment has its own dedicated RF chain. This allows for advanced digital signal processing like Maximal-Ratio Combining (MRC).

The researchers developed PA placement algorithms to optimize exactly where the "clothespins" should be snapped onto each segment to maximize the Signal-to-Noise Ratio (SNR). They also derived closed-form mathematical expressions to predict how performance scales as you add more segments.

Datasets

As a theoretical and architectural paper, no external datasets were used. Instead, the authors validated their models using Monte Carlo simulations with parameters aligned with 5G/6G expectations:

  • Carrier Frequency: 28 GHz (Millimeter wave).
  • Environment: A rectangular service region (e.g., 100m x 20m).
  • Channel Model: Free-space Line-of-Sight (LoS) combined with an exponential attenuation model for the waveguide.

Key Insights and Ideas

  • Divide and Conquer for Math: By ensuring only one PA is active per segment in the uplink, the IAR effect is physically eliminated. This finally allows for a "tractable and physically consistent" uplink signal model.
  • The "Double Benefit" of Shortness: Shorter segments reduce the distance a signal travels inside the waveguide and ensure the active antenna is always relatively close to the user. This mitigates both large-scale path loss and waveguide attenuation.
  • Linear Scaling: Under the Segment Multiplexing (SM) protocol, the received SNR scales linearly with the number of segments, effectively turning the waveguide into a distributed massive MIMO system.
  • Phase Matters: In the Aggregation (SA) protocol, simply adding more segments isn't always better. If segments are too far from the user, they add more noise than signal, leading to a "non-monotonic" performance curve where there is an optimal number of active segments.

Key Results

  • SM is King: Segment Multiplexing consistently achieves the highest performance, followed by Aggregation and then Selection.
  • SWAN vs. Conventional: In all scenarios, the segmented approach (SWAN) significantly outperformed the single-waveguide approach (PASS).
  • Efficiency: Numerical results showed that even with a modest number of segments (e.g., 9 segments for a 100m area), in-waveguide loss could be reduced to negligible levels (achieving >0.9 propagation gain).
  • Stability: While conventional PASS performance tanks as the service area grows (due to increasing waveguide length), SWAN maintains stable performance because each segment remains short and efficient.

Limitations and Future Work

  • Hardware Complexity: While SM performs best, it requires multiple RF chains, which increases cost and power consumption compared to the single-chain SA or SS protocols.
  • Single User Focus: This paper focuses on a single-user scenario. The authors note that future work is needed to explore multi-user interference and how to optimally assign segments to different users simultaneously.
  • Hybrid Protocols: The authors briefly mention "Hybrid" protocols (HSS/A and HSS/M) that could balance performance and complexity, marking them as a promising direction for future research.

Summary updated

Abstract

A segmented waveguide-enabled pinching-antenna system (SWAN) is proposed, in which a segmented waveguide composed of multiple short dielectric waveguide segments is employed to radiate or receive signals through the pinching antennas (PAs) deployed on each segment. Based on this architecture, three practical operating protocols are proposed: segment selection (SS), segment aggregation (SA), and segment multiplexing (SM). For uplink SWAN communications, where one PA is activated per segment, the segmented structure eliminates the inter-antenna radiation effect, i.e., signals captured by one PA may re-radiate through other PAs along the same waveguide. This yields a tractable and physically consistent uplink signal model for a multi-PA pinching-antenna system (PASS), which has not been established for conventional PASS using a single long waveguide. Building on this model, PA placement algorithms are proposed to maximize the uplink signal-to-noise ratio (SNR). Closed-form expressions for the received SNR under the three protocols are derived, and the corresponding scaling laws with respect to the number of segments are analyzed. It is proven that the segmented architecture reduces both the average PA-to-user distance and the PA-to-feed distance, thereby mitigating both large-scale path loss and in-waveguide propagation loss. These results are extended to downlink SWAN communications, where multiple PAs are activated per segment, and PA placement methods are proposed to maximize the downlink received SNR under the three protocols. Numerical results demonstrate that: \romannumeral1) among the three protocols, SM achieves the best performance, followed by SA and then SS; and \romannumeral2) for all protocols, the proposed SWAN achieves a higher SNR than conventional PASS with a single long waveguide in both uplink and downlink scenarios.
BibTeX
@article{ouyang2026uplink,
  author = {Chongjun Ouyang and Hao Jiang and Zhaolin Wang and Yuanwei Liu and Zhiguo Ding},
  title = {{Uplink and Downlink Communications in Segmented Waveguide-Enabled Pinching-Antenna Systems (SWANs)}},
  journal = {IEEE Trans. Communications},
  year = {2026},
  doi = {10.1109/tcomm.2026.3653885},
}
Figure