Abstract: Thin films of seven common polymers—polyethylene, polystyrene, polymethyl methacrylate, polypropylene, polycarbonate, polyethylene terephthalate, and polytetrafluoroethylene—were irradiated with $2.8 \times 10^6$ r of $\gamma$-rays at room temperature. Following irradiation, the absorption current ($i_a$) was measured under a DC voltage, and the decay constant $n$ was derived from the empirical formula $i_a = At^{-n}$. The results show that $\gamma$-ray exposure significantly slows the decay rate of the absorption current. While polystyrene demonstrated a full recovery of its electrical properties within 360 hours, most other plastics retained a measurable "radiation hangover." This study reveals that absorption current decay is a highly sensitive indicator of radiation damage, manifesting changes at doses significantly lower than those required to alter bulk resistivity.
Introduction
In high-precision electrical engineering, the behavior of insulators under DC voltage is a critical factor. When a voltage is applied to a plastic insulator, the current does not immediately drop to its steady-state value. Instead, it undergoes a slow, power-law decay known as the absorption current. This phenomenon is fundamentally linked to dielectric relaxation and the movement of trapped charges within the polymer matrix.
Historically, plastic insulators were considered relatively resistant to radiation, with significant electrical degradation typically expected only at doses between $10^7$ and $10^9$ roentgens (r). However, this 1963 study from the Japan Defence Agency’s Technical Research Institute challenges that assumption by focusing on the sensitivity of the absorption current to lower-level $\gamma$-ray exposure.
Experimental Methodology
The researchers investigated seven widely used polymers: Polyethylene (PE), Polystyrene (PS), Polymethyl methacrylate (PMMA), Polypropylene (PP), Polycarbonate (PC), PET (Mylar), and PTFE (Teflon). Samples were prepared as thin films (0.06 to 0.12 mm) with aluminum foil electrodes.
Each sample was exposed to $\gamma$-rays from a Cobalt-60 ($^{60}\text{Co}$) source, receiving a total dose of $2.8 \times 10^6$ r. After irradiation, a 92V DC charge was applied, and the resulting current decay was monitored for approximately two hours ($7.2 \times 10^3$ seconds). The decay was modeled using the empirical power-law equation:
$$i_a = At^{-n}$$
In this model, $i_a$ represents the absorption current, $t$ is the time elapsed since voltage application, and $n$ is the decay constant. A higher $n$ value indicates a rapid return to equilibrium, while a lower $n$ signifies a lingering current, often associated with increased charge trapping or structural defects.
Key Results and the "Memory" Effect
The study found that immediately following irradiation, the decay constant $n$ dropped sharply across all materials. This indicates that the radiation made the insulators "leakier" for extended periods, as the current took much longer to dissipate compared to the pre-irradiated state.
The Recovery Curve
A central finding of the research was the varying ability of these plastics to "heal" over time. By measuring the decay constant at intervals up to 360 hours after the radiation source was removed, the authors mapped the recovery of the materials' electrical properties.
- Polystyrene (PS): Stood out as the most resilient material. It began recovering almost immediately and returned to its original decay constant ($n \approx 0.85$) within 150 hours.
- Polyethylene (PE) and Teflon (PTFE): These materials exhibited a significant "memory" of the radiation event. Even after 15 days (360 hours), their $n$ values remained substantially lower than their pre-irradiation baselines, suggesting semi-permanent structural changes or long-lived charge traps.
Discussion and Implications
The most significant insight from this work is the sensitivity of the absorption current. While bulk resistivity or dielectric constants might remain unchanged at $10^6$ r, the decay constant $n$ provides a clear signature of radiation-induced modification. The recovery of $n$ closely mirrors the recovery of general electrical conductivity, suggesting that both are governed by the same underlying physical mechanisms—likely the generation and subsequent trapping/recombination of electrons and holes.
The researchers noted that the presence of air during irradiation likely influenced the results, as oxygen can facilitate polymer degradation. Future studies were suggested to explore these effects in a vacuum and to map the dose-response relationship more granularly.
Conclusion
This research demonstrates that plastic insulators are more sensitive to $\gamma$-ray radiation than previously believed. The persistent change in the absorption current decay constant $n$ serves as a sensitive metric for radiation damage. While some materials like polystyrene can self-heal relatively quickly, others retain an electrical "memory" of the exposure for weeks, a factor that must be considered in the design of electronic components for radiation-prone environments.
Reference: Ide, S., Urai, T., & Saito, H. (1963). Transient Current from Plastic Insulators and its Change by $\gamma$-Ray Irradiation. Kobunshi Kagaku, 20(222), 583-586.
Summary updated