Towards Touch-to-Access Device Authentication Using Induced Body Electric Potentials

Zhenyu Yan, Qun Song, Rui Tan, Yang Li, Adams Wai-Kin Kong

Introduction

As smart environments expand, the number of connected devices in homes and offices is skyrocketing. Managing access to these devices—from smart toasters to office equipment—presents a significant usability and security challenge. Traditional authentication methods like passwords are impractical for screenless devices, while biometric hardware like fingerprint scanners is often too expensive and power-intensive for low-cost IoT nodes.

TouchAuth introduces a "touch-to-access" paradigm. It leverages the human body as an antenna to capture ambient electrical noise from indoor wiring, enabling secure authentication through a simple touch. By comparing induced body electric potentials (iBEP) measured by a wearable "authenticator" and a smart "authenticatee," the system verifies that both are being touched by the same authorized individual.

System Architecture and Protocol

The TouchAuth system consists of two primary components: an authorized wearable (e.g., a smartwatch) and a target smart object. Both devices are equipped with standard Analog-to-Digital Converter (ADC) pins to sample the iBEP signal.

The TouchAuth system overview showing the physical interaction and the authentication protocol sequence.

The authentication process follows a structured protocol:

  1. Initialization & Secure Channel: The devices establish a TLS connection and synchronize their clocks.
  2. iBEP Sampling: Both devices simultaneously sample the ambient electrical noise through the user's skin.
  3. Secure Exchange: Using a commitment-based "H2H" protocol, the devices exchange their sampled data. This prevents man-in-the-middle attacks where an adversary might attempt to replay or forge signals.
  4. Correlation Analysis: The system calculates the Absolute Pearson Correlation Coefficient (APCC) between the two signals. A high correlation indicates that the signals originated from the same human body, leading to an "accept" decision.

The Body Antenna Effect

The fundamental principle behind TouchAuth is the Body Antenna Effect. Indoor environments are permeated by 50/60Hz electric fields (EF) emitted by AC power lines. When a person touches an electrode, their body acts as a large conductor, significantly altering the local EF and inducing a measurable potential.

Comparison of iBEP signals with and without skin contact, demonstrating the significant signal amplification when the body acts as an antenna.

Because the human body is a conductor, it acts as an equipotential surface. Two sensors touching the same person will observe highly correlated potential fluctuations relative to the body's reference, even if their own "floating grounds" differ. This spatial sensitivity ensures that even individuals standing close to each other will have distinct iBEP signatures, providing a robust layer of security against accidental cross-authentication.

Key Results and Performance

TouchAuth was evaluated with 12 participants across 8 diverse indoor environments, including kitchens and laboratories. The system demonstrated high accuracy and efficiency:

  • Speed and Accuracy: With only 1 second of sampling, the system achieves a 94.2% True Acceptance Rate (TAR). Extending the sampling time to 5 seconds increases the TAR to 98.9%, with a False Acceptance Rate (FAR) of just 2%.
  • Robustness: The system maintains performance in the presence of high-power appliance noise (e.g., heaters, blenders) and active cellular interference.
  • Efficiency: Compared to physiological signals like ECG or PPG, which often require 30–60 seconds of data, TouchAuth provides near-instantaneous authentication using ubiquitous, low-cost hardware.

Limitations and Future Outlook

While highly effective indoors, TouchAuth relies on the presence of ambient electric fields from building wiring, making it unsuitable for outdoor use. Additionally, the signal correlation decreases as the distance between sensors on the body increases (e.g., wrist to head), which serves as a natural security boundary but limits certain wearable configurations.

Future research will focus on further miniaturizing the sensing electrodes and integrating TouchAuth into a broader range of consumer electronics, potentially replacing traditional pairing and login methods with a simple, intuitive touch.

Summary updated

Abstract

This paper presents TouchAuth, a new touch-to-access device authentication approach using induced body electric potentials (iBEPs) caused by the indoor ambient electric field that is mainly emitted from the building's electrical cabling. The design of TouchAuth is based on the electrostatics of iBEP generation and a resulting property, i.e., the iBEPs at two close locations on the same human body are similar, whereas those from different human bodies are distinct. Extensive experiments verify the above property and show that TouchAuth achieves high-profile receiver operating characteristics in implementing the touch-to-access policy. Our experiments also show that a range of possible interfering sources including appliances' electromagnetic emanations and noise injections into the power network do not affect the performance of TouchAuth. A key advantage of TouchAuth is that the iBEP sensing requires a simple analog-to-digital converter only, which is widely available on microcontrollers. Compared with existing approaches including intra-body communication and physiological sensing, TouchAuth is a low-cost, lightweight, and convenient approach for authorized users to access the smart objects found in indoor environments.
BibTeX
@inproceedings{yan2019towards,
  author = {Zhenyu Yan and Qun Song and Rui Tan and Yang Li and Adams Wai-Kin Kong},
  title = {{Towards Touch-to-Access Device Authentication Using Induced Body Electric Potentials}},
  booktitle = {MobiCom},
  year = {2019},
  doi = {10.1145/3300061.3300118},
}
Figure