Thermal assisted up-conversion electroluminescence in quantum dot light emitting diodes

Qiang Su, Shuming ChenNature Communications 2022 · DOI

TL;DR

Researchers have uncovered the mechanism behind "up-conversion electroluminescence" in quantum dot light-emitting diodes (QLEDs), where emitted light has higher energy than the input electrons. They found that thermal energy is crucial for enabling hole injection into quantum dots at voltages below their bandgap, paving the way for more efficient QLEDs.

What Problem Does This Paper Address?

Quantum dot light-emitting diodes (QLEDs) are highly promising for next-generation displays due to their vibrant colors, high efficiency, and low-cost fabrication. A key characteristic of QLEDs is their electroluminescence (EL), where electrons and holes injected into quantum dots (QDs) recombine to emit light. Ideally, the energy of the emitted photon ($hv$) should be equal to or less than the energy of the injected electrons ($eV$), meaning the turn-on voltage ($V_T$) should be at least $hv/e$. However, researchers have frequently observed "sub-bandgap turn-on," where detectable EL occurs at voltages significantly lower than $hv/e$. This phenomenon, known as up-conversion electroluminescence, implies that the emitted photon's energy is higher than the electron's initial energy. While this effect has been observed in various devices, its underlying mechanism, particularly how holes are injected into QDs at these low voltages, has remained unclear and debated. Existing explanations, like Auger-assisted processes, have been disproven by experimental evidence showing efficiencies exceeding theoretical limits.

Methods

The researchers investigated the mechanism of up-conversion electroluminescence by systematically studying the effect of temperature on the charge injection dynamics in QLEDs. Their approach involved:

  • Temperature-Dependent Electroluminescence (EL) Measurements: They measured current-voltage-luminance (J-V-L), capacitance-voltage (C-V), and transient EL characteristics of QLEDs across a wide temperature range (from -100 °C to 160 °C). This allowed them to observe how temperature influences the turn-on voltage ($V_T$) and emission intensity.
  • Theoretical Analysis: They employed theoretical models to analyze the energy levels of the device layers and the charge injection barriers. This included modeling thermionic emission and Coulombic interactions to understand how holes overcome the energy barriers.
  • Device Fabrication: They fabricated QLEDs with different structures and materials (e.g., using TFB, PVK, or CBP as hole transport layers) to demonstrate the universality of the observed mechanism. They also fabricated "hole-only" devices to specifically study hole transport.

Datasets

Not discussed in the paper. The study relies on experimental measurements from fabricated devices rather than pre-existing datasets.

Key Insights and Ideas

  • Thermal Energy is Key: The most significant finding is that thermal energy plays a critical role in enabling hole injection into QDs at sub-bandgap voltages. Without sufficient thermal energy, hole injection is severely hindered by a large energy barrier.
  • Thermal-Assisted Thermionic Emission: The paper elucidates that holes are injected via a "thermal-assisted thermionic-emission mechanism." This means that thermal energy provides holes with enough kinetic energy to overcome the energy barrier at the TFB/QD interface.
  • Sub-Bandgap Turn-On Explained: This mechanism directly explains the observed sub-bandgap turn-on. At voltages below the bandgap, electrons can be injected, and with the help of thermal energy, holes can also be injected, leading to exciton formation and light emission.
  • Universal Mechanism: The study demonstrates that this thermal-assisted hole injection is a universal mechanism responsible for up-conversion EL, observed across different QLED structures and colors.
  • Beyond Auger: The findings definitively rule out Auger-assisted processes as the primary mechanism for up-conversion EL, as the observed efficiencies exceed the theoretical limits of such processes.

Key Results

  • Reduced Turn-On Voltage with Temperature: For red, green, and blue QLEDs, the turn-on voltage ($V_T$) significantly decreased as temperature increased. For example, the $V_T$ for red QLEDs dropped from 1.6 V at room temperature (RT) to 1.25 V at 160 °C.
  • High Up-Conversion Efficiency: The up-conversion efficiency (defined as $V_{ph}/V_T$) was found to be significantly higher than 100% (e.g., 125% for red QLEDs at RT), and this efficiency increased with temperature.
  • External Quantum Efficiency (EQE) Above Auger Limit: The EQE of the QLEDs at sub-bandgap bias reached up to 12.5-15%, which is higher than the theoretical ~10% upper limit for Auger-assisted processes.
  • Theoretical Model Agreement: The theoretical calculations for luminance based on thermal-assisted thermionic emission showed good agreement with experimental measurements, especially at lower temperatures.
  • Faster Transient Response: At elevated temperatures, QLEDs showed a more rapid turn-on in transient EL measurements, indicating enhanced hole injection.

Limitations and Future Work

  • Limitations: While the study provides a strong explanation for the mechanism, the exact contribution of thermal energy versus field-assisted injection at higher voltages could be further refined. The paper also notes that at very high temperatures, the discrepancy between calculated and measured luminance is attributed to increased hole concentration due to thermal excitation, suggesting that more complex models might be needed for extreme conditions.
  • Future Work: The authors suggest that their findings pave the way for developing up-conversion QLEDs with power conversion efficiencies exceeding 100%. Future research could focus on optimizing device structures and materials to maximize the benefits of thermal-assisted hole injection for even higher performance and efficiency. Further exploration into controlling and leveraging thermal effects in QLEDs could lead to novel device functionalities.

Summary updated

Abstract

Up-conversion electroluminescence, in which the energy of a emitted photon is higher than that of the excitation electron, is observed in quantum-dot light-emitting diodes. Here, we study its mechanism by investigating the effect of thermal energy on the charge injection dynamic. Based on the results of temperature-dependent electroluminescence and theoretical analysis, we reveal that at sub-bandgap voltage, holes can be successfully injected into quantum-dots via thermal-assisted thermionic-emission mechanism, thereby enabling the sub-bandgap turn-on and up-conversion electroluminescence of the devices. Further theoretical deduction and experimental results confirm that thermal-assisted hole-injection is the universal mechanism responsible for the up-conversion electroluminescence. This work uncovers the charge injection process and unlocks the sub-bandgap turn-on mechanism, which paves the road for the development of up-conversion devices with power conversion efficiency over 100%.
BibTeX
@inproceedings{su2022thermal,
  author = {Qiang Su and Shuming Chen},
  title = {{Thermal assisted up-conversion electroluminescence in quantum dot light emitting diodes}},
  booktitle = {Nature Communications},
  year = {2022},
  doi = {10.1038/s41467-022-28037-w},
}

Loading related content...

Figure