The Design of Battery Protection Circuit and Its Application in Solar Street Lamp

Weiwei Liang, Jungang Zhou, Huanqi Zheng, Nianxing Shi, Honglian Wang2016 · DOI

Abstract

Solar panels convert solar energy into electrical energy stored in the battery and provide power for the solar street lamp. The voltage of solar panel power supplying is not stable, resulting in the problem of over charge and over discharge for battery in the use process of solar street lamp. The above problems lead to the battery life is reduced, and the service life of the solar street lamp is directly affected. In order to solve the above problems, the protective circuit of the battery was designed in this paper, including charging circuit design, discharging circuit design, voltage detection circuit design and current detection circuit design.

Introduction

Solar street lamps are a critical component of sustainable urban infrastructure. However, their reliability is often compromised by the "weakest link" in the system: the storage battery. Solar panels generate highly variable voltage based on environmental conditions, which frequently leads to chronic overcharging during peak daylight and over-discharging at night. Research indicates that approximately 95% of premature battery failures in these systems are attributable to these two issues. Without adequate electronic protection, a battery's service life is typically limited to 1–2 years. Given that batteries represent the most significant maintenance cost, extending their lifespan is vital for the economic viability of solar lighting.

System Architecture and Methodology

The proposed system utilizes a microcontroller (MCU) to manage a four-part circuit architecture designed to stabilize operations and protect hardware components.

Charging Circuit Design

The charging system moves beyond simple on/off switching by implementing a "float and pulse" strategy. The MCU monitors light intensity and battery voltage via A/D conversion. An IRFZ44N MOSFET serves as the primary switching element. As the battery approaches its "float point," the system transitions from high-current charging to high-frequency pulse charging. This method reduces chemical stress and prevents overheating, ensuring the battery reaches a true full state safely.

The schematic diagram of the charging circuit featuring the IRFZ44N MOSFET and solar input.

Discharging Circuit Design

To protect both the LED load and the battery, the discharge phase is managed via Pulse Width Modulation (PWM). When a battery is fully charged (reaching 24.6V–25.6V), a direct connection would drive LED currents up to 31.5mA, far exceeding the standard 20mA limit and risking burnout. The PWM controller regulates the effective voltage to a stable 24V, maintaining optimal current levels. A $du/dt$ suppression (snubber) circuit is included to protect the switching transistors from voltage spikes during high-speed PWM operations.

The discharging circuit design incorporating PWM control and a snubber circuit for load protection.

Detection Circuits

  • Voltage Detection: A scaling circuit utilizing an LM358 operational amplifier maps the 0–26V battery range to a 0–3.3V signal, allowing the MCU to monitor voltage levels with high precision.
  • Current Detection: Using a 0.01Ω sampling resistor and an LM358 amplifier with a 23x magnification factor, the system tracks charging and discharging trends to inform the MCU's control logic.

Key Results and Discussion

Experimental validation of the prototype demonstrated significant improvements in system performance:

  • Lifespan Extension: The implementation of intelligent protection more than doubled the battery's service life, increasing it from an average of 1.5 years to over 3 years.
  • Voltage and Current Stability: The system successfully maintained battery voltage within the 23.5V–25V range. LED current was strictly regulated within the 15–20mA window, preventing the dangerous 26.7–31.5mA over-current conditions seen in unprotected systems.
  • Operational Logic: The MCU successfully implemented a 1-minute delay after sensing low solar voltage (<1V) before activating the LEDs, effectively eliminating flickering during dusk or transient cloud cover.

Conclusion

The design of a comprehensive battery protection circuit is essential for the longevity of solar street lamps. By combining pulse charging, PWM-controlled discharging, and precise sensing, this system mitigates the primary causes of battery failure. While future iterations could benefit from temperature compensation to handle extreme climates, the current design provides a robust solution for extending the operational life and reducing the maintenance costs of green lighting infrastructure.

Reference: Liang, W., Zhou, J., Zheng, H., Shi, N., & Wang, H. (2016). The Design of Battery Protection Circuit and Its Application in Solar Street Lamp. Proceedings of the 2nd Information Technology and Mechatronics Engineering Conference (ITOEC 2016).

Summary updated

Abstract

Solar panels convert solar energy into electrical energy stored in the battery and provide power for the solar street lamp. The voltage of solar panel power supplying is not stable, resulting in the problem of over charge and over discharge for battery in the use process of solar street lamp. The above problems lead to the battery life is reduced, and the service life of the solar street lamp is directly affected. In order to solve the above problems, the protective circuit of the battery was designed in this paper, including charging circuit design, discharging circuit design, voltage detection circuit design and current detection circuit design.
BibTeX
@misc{liang2016design,
  author = {Weiwei Liang and Jungang Zhou and Huanqi Zheng and Nianxing Shi and Honglian Wang},
  title = {{The Design of Battery Protection Circuit and Its Application in Solar Street Lamp}},
  year = {2016},
  doi = {10.2991/itoec-16.2016.72},
}
Figure