Tailored Fabrication of 3D Nanopores with Dielectric Oxides for Multiple Nanoscale Applications

Germàn Lanzavecchia, Аnastasiia S. Sapunova, Ali Douaki, Shukun Weng, Dmitry Momotenko, Gonçalo Paulo, Alberto Giacomello, Roman Krahne, Denis GaroliarXiv 2024 · DOI · arXiv

Abstract

Nanopore sensing is a key technology for single-molecule detection and analysis. Solid-state nanopores have emerged as a versatile platform, since their fabrication allows to engineer their properties by controlling size, shape, and chemical functionalization. However, lithography-based fabrication approaches for non-planar nanopores-on-chip rely on polymers that have limits with respect to hard- and robustness, durability, and refractive index. In this respect, nanopores made of metal oxides with high dielectric constant would be much more favourable and have the potential to extend the suitability of solid-state nanopores towards optoelectronic technologies. Here, we present a versatile method to fabricate three-dimensional nanopores of different dielectric oxides with controlled shapes. Our approach uses photoresist only as a template in the focused-ion-beam lithography to define the nanopore shape, which is subsequently coated with different oxides ($SiO_2$, $Al_2O_3$, $TiO_2$ and $HfO_2$) by atomic-layer deposition. Then the photoresist is fully removed by chemo-physical treatment, resulting in nanopores entirely made from dielectric oxides on a thin solid-state membrane. Our methodology allows straightforward fabrication of convex, straight, and concave nanopore shapes that can be employed in various technologies and applications. We explored their performance as ionic nanochannels and investigated the dependence of the ionic current rectification on the nanopore geometry. We found hysteresis in the ionic conductance that enables potential applications of the nanopores in memristors. We also investigated the dielectric oxide nanopores for DNA sensing by measuring both cis-trans and trans-cis translocations and support our data with numerical simulations based on the Poisson-Nernst-Planck model.

Introduction

Nanopore sensing has become a cornerstone of single-molecule analysis, yet the field faces a significant material science bottleneck. While solid-state nanopores offer greater durability than biological alternatives, creating complex 3D geometries—such as conical or "trumpet" shapes—traditionally relies on polymer-based lithography. These polymers are often chemically fragile and possess low refractive indices, limiting their integration into advanced optoelectronic or photonic systems.

Metal oxides, characterized by high dielectric constants and superior durability, are ideal candidates for these applications but are notoriously difficult to sculpt into precise 3D architectures on-chip. This research presents a versatile "template-and-coat" fabrication route to produce all-oxide 3D nanopores, bridging the gap between complex geometry and robust material properties.

Fabrication Methodology

The core of this work is a sacrificial template approach that enables nanometer-scale control over 3D structures. The process begins with a silicon nitride membrane coated in photoresist.

  1. Mold Creation: Focused Ion Beam (FIB) lithography is used to mill concentric disks of varying diameters. Secondary radiation from the beam cross-links and hardens a ~50nm layer of photoresist, forming a precise 3D "mold."
  2. Oxide Deposition: Atomic Layer Deposition (ALD) is then employed to coat the backside of the membrane and the mold with dielectric oxides ($SiO_2$, $Al_2O_3$, $TiO_2$, or $HfO_2$).
  3. Sacrificial Removal: The hardened photoresist template is removed through a combination of UV light (to break cross-links) and either low-power oxygen plasma or thermal annealing at 650°C.
Schematic of the 3D nanopore fabrication process and its applications in ion transport and DNA sensing.

Characterization and Results

The resulting structures were characterized using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) to confirm their geometry and material composition. The methodology successfully produced nanopores with apertures as small as ~7 nm in various configurations, including concave, convex, and straight profiles.

SEM and EDS characterization of fabricated 3D nanopores showing various geometries and material composition.

Ionic Transport and Memristive Behavior

The 3D geometry of the pores significantly influences ionic movement. The "half-cone angle" at the pore tip was identified as the primary driver of Ionic Current Rectification (ICR), where the pore acts as a diode. Notably, these nanopores exhibit memristive behavior—a "memory" effect where conductance depends on the history of applied voltage. This phenomenon arises from the redistribution of ions within the 3D channel over diffusive timescales, mimicking synaptic plasticity.

DNA Sensing Performance

In DNA translocation experiments using $\lambda$-DNA, the conical geometry introduced a functional asymmetry. DNA moving from "tip-to-base" yielded a higher signal-to-noise ratio and occurred twice as frequently as "base-to-tip" movement. A relative signal ($ΔI/I_0$) of 11% was achieved for tip-to-base translocations, demonstrating enhanced sensitivity compared to standard cylindrical pores.

Conclusion and Future Outlook

This fabrication platform successfully overcomes the limitations of polymer-based 3D nanopores. By utilizing robust dielectric oxides, these structures are suited for harsh environments and advanced sensing modalities. Future work may involve the integration of metallic layers to create tunable plasmonic antennas or the use of high-refractive-index oxides like $TiO_2$ for "Mie-tronics," enabling simultaneous electrical and optical single-molecule detection on a single chip.

Summary updated

Abstract

Nanopore sensing is a key technology for single-molecule detection and analysis. Solid-state nanopores have emerged as a versatile platform, since their fabrication allows to engineer their properties by controlling size, shape, and chemical functionalization. However, lithography-based fabrication approaches for non-planar nanopores-on-chip rely on polymers that have limits with respect to hard- and robustness, durability, and refractive index. In this respect, nanopores made of metal oxides with high dielectric constant would be much more favourable and have the potential to extend the suitability of solid-state nanopores towards optoelectronic technologies. Here, we present a versatile method to fabricate three-dimensional nanopores of different dielectric oxides with controlled shapes. Our approach uses photoresist only as a template in the focused-ion-beam lithography to define the nanopore shape, which is subsequently coated with different oxides (SiO2, Al2O3, TiO2 and HfO2) by atomic-layer deposition. Then the photoresist is fully removed by chemo-physical treatment, resulting in nanopores entirely made from dielectric oxides on a thin solid-state membrane. Our methodology allows straightforward fabrication of convex, straight, and concave nanopore shapes that can be employed in various technologies and applications. We explored their performance as ionic nanochannels and investigated the dependence of the ionic current rectification on the nanopore geometry. We found hysteresis in the ionic conductance that enables potential applications of the nanopores in memristors. We also investigated the dielectric oxide nanopores for DNA sensing by measuring both cis-trans and trans-cis translocations and support our data with numerical simulations based on the Poisson-Nernst-Planck model.
BibTeX
@misc{lanzavecchia2024tailored,
  author = {Germàn Lanzavecchia and Аnastasiia S. Sapunova and Ali Douaki and Shukun Weng and Dmitry Momotenko and Gonçalo Paulo and Alberto Giacomello and Roman Krahne and Denis Garoli},
  title = {{Tailored Fabrication of 3D Nanopores with Dielectric Oxides for Multiple Nanoscale Applications}},
  year = {2024},
  eprint = {2405.02632},
  archivePrefix = {arXiv},
  url = {https://arxiv.org/abs/2405.02632},
}
Figure