Study on the Flow Characteristics and Heating Performance of a Drilling Fluid Helical Heater

Yi ZhangThyssenKrupp 2025 · DOI

TL;DR

Researchers have developed and validated a spiral-finned helical heater designed to improve the efficiency of gas logging in petroleum drilling. By moving away from clog-prone straight-tube designs and optimizing helical geometry, the study demonstrates how to significantly enhance heat transfer in highly viscous, non-Newtonian drilling fluids.

What Problem Does This Paper Address?

In the world of petroleum drilling, "gas logging" is the process of analyzing hydrocarbon gases trapped in the drilling fluid (mud) returning from a well. To get an accurate reading, the mud must be passed through a degasser. Heating the mud before it enters the degassing chamber is essential because warmer fluids release entrained gases more easily.

However, drilling mud is a "nightmare" fluid for engineers: it is dense, highly viscous, and packed with solids. Conventional straight-tube heaters frequently clog, leading to maintenance headaches and inaccurate data. While spiral heaters are known for better heat transfer, there has been a lack of specific research on how their geometry (like fin thickness and pitch) interacts with the complex, non-Newtonian behavior of drilling mud. This paper aims to fill that gap by finding the "Goldilocks" configuration for a helical heater.

Methods

The authors employed a dual-track approach:

  1. Numerical Simulation (CFD): They used Computational Fluid Dynamics to model the fluid flow and heat transfer. Crucially, they didn't treat the mud like water. They used the Herschel-Bulkley (H-B) model to account for the fluid's non-Newtonian characteristics, such as yield stress (the force needed to get it moving) and shear-thinning (it gets thinner as it moves faster). They utilized a standard $k-\epsilon$ turbulence model to simulate the complex flow around the spirals.
  2. Experimental Validation: To ensure their simulations weren't just "pretty pictures," the team built a physical test bench featuring an electric heater, a pump, and temperature sensors. They tested two different helix pitches (28mm and 38mm) across various flow rates to see how well the real-world results matched their digital twin.

Datasets

This study did not use public machine learning datasets. Instead, the "data" consisted of:

  • Measured Thermophysical Properties: The authors used specific measured values for drilling fluid density ($1.15\text{ g/cm}^3$), viscosity ($21\text{ mPa}\cdot\text{s}$), and thermal conductivity ($0.82\text{ W}\cdot\text{m}^{-1}\cdot\text{°C}^{-1}$) to feed their simulations.
  • Experimental Benchmarks: The primary evaluation metrics were the Nusselt number (Nu)—which characterizes the intensity of convective heat transfer—and the fluid outlet temperature.

Key Insights and Ideas

  • The "4mm Anomaly": Generally, you might expect the thinnest fins to allow for the most fluid volume and thus specific heating patterns. However, the researchers found that a 4mm fin thickness exhibited a unique advantage. At high flow rates (high Reynolds numbers), the 4mm fin actually produced higher outlet temperatures than the 2mm fin. This suggests that specific thicknesses create more favorable turbulence or residence times for heat to soak into the viscous mud.
  • The Pitch Trade-off: A smaller fin pitch (28mm vs. 58mm) significantly improves heating performance because it forces the fluid into a longer, more tortuous path. The "aha moment" here is the cost: the 28mm pitch resulted in a pressure drop of 10,470 Pa, nearly five times higher than the 58mm pitch (2,371 Pa). Engineers must balance heating efficiency against the pumping power required.
  • Non-Newtonian Necessity: The study reinforces that simpler rheological models fail in this field. By accounting for temperature-dependent yield stress and consistency indices, the model accurately predicted how mud "thins" near the heated walls, which is where the most critical heat transfer occurs.

Key Results

  • Heat Transfer Intensity: The Nusselt number (Nu) increased steadily with the Reynolds number (Re). Thicker fins generally yielded higher Nu values, though the gains diminished as the fins got thicker (e.g., the difference between 8mm and 10mm was negligible).
  • Temperature Gains: Increasing the heat flux density from $10\text{ W/cm}^2$ to $20\text{ W/cm}^2$ resulted in a nearly linear increase in the bulk mean temperature of the fluid.
  • Simulation vs. Reality: The experimental outlet temperatures were consistently about 12°C lower than the simulation results at low flow rates. The authors attributed this to real-world thermal dissipation (heat leaking out of the system) that the idealized "adiabatic" simulation didn't fully capture.

Limitations and Future Work

The most prominent limitation is the thermal loss gap between the CFD model and the physical experiment. While the trends matched perfectly, the 12°C discrepancy suggests that future models need to better account for environmental heat loss rather than assuming perfect insulation.

Additionally, the study focused on a "clean" drilling fluid. In actual drilling operations, the fluid is often contaminated with rock cuttings and gas bubbles of varying sizes. Future research could investigate multi-phase flow—how the presence of actual gas bubbles and solid debris affects the heat transfer and potential for erosion within the spiral channels.

Summary updated

Abstract

Gas logging technology plays a critical role in petroleum drilling. Within this system, the degasser serves as a key component, and the heater is an essential part of the degassing unit. Heating the drilling fluid promotes more efficient liberation of hydrocarbon gases, thereby enhancing the accuracy of gas logging. Therefore, improving the heater’s heat transfer performance is of significant importance for optimizing logging operations. In this study, numerical simulation is employed to investigate the heating and flow characteristics of return drilling fluid inside the channels of a spiral heater. The effects of the heater’s structural parameters and the operational conditions of the drilling fluid on its heating performance are systematically analyzed. Furthermore, experimental studies on the spiral heater were conducted, and the differences between numerical simulations and experimental results were evaluated for two different helix pitches under varying flow rates.
BibTeX
@inproceedings{zhang2025study,
  author = {Yi Zhang},
  title = {{Study on the Flow Characteristics and Heating Performance of a Drilling Fluid Helical Heater}},
  booktitle = {ThyssenKrupp},
  year = {2025},
  doi = {10.71448/tk202544},
}
Figure