Abstract
Modern millimeter wave (mmWave) communication systems rely on beam alignment to deliver sufficient beamforming gain to close the link between devices. We present a novel beam selection methodology for multi-panel, full-duplex mmWave systems, which we call STEER, that delivers high beamforming gain while significantly reducing the full-duplex self-interference coupled between the transmit and receive beams. STEER does not necessitate changes to conventional beam alignment methodologies nor additional over-the-air feedback, making it compatible with existing cellular standards. Instead, STEER uses conventional beam alignment to identify the general directions beams should be steered, and then it makes use of a minimal number of self-interference measurements to jointly select transmit and receive beams that deliver high gain in these directions while coupling low self-interference. We implement STEER on an industry-grade 28 GHz phased array platform and use further simulation to show that full-duplex operation with beams selected by STEER can notably outperform both half-duplex and full-duplex operation with beams chosen via conventional beam selection. For instance, STEER can reliably reduce self-interference by more than 20 dB and improve SINR by more than 10 dB, compared to conventional beam selection. Our experimental results highlight that beam alignment can be used not only to deliver high beamforming gain in full-duplex mmWave systems but also to mitigate self-interference to levels near or below the noise floor, rendering additional self-interference cancellation unnecessary with STEER.
Introduction
Millimeter-wave (mmWave) communication is a cornerstone of next-generation wireless networks, providing the bandwidth necessary for multi-gigabit throughput. Current deployments primarily utilize Time Division Duplexing (TDD), which limits spectral efficiency by separating transmission and reception in time. Full-duplex (FD) operation promises to double this efficiency but faces a significant challenge: self-interference (SI). In FD systems, the high-power local transmitter leaks into the sensitive local receiver, often masking the desired remote signal.
Conventional beam alignment techniques are designed to maximize the Signal-to-Noise Ratio (SNR) by pointing beams directly at the intended target. However, as illustrated in Figure 1, these "best" beams often result in high SI coupling. We present STEER, a beam selection methodology that jointly optimizes for beamforming gain and SI mitigation.
The STEER Methodology
STEER (Beam Selection for Full-Duplex Millimeter Wave Communication Systems) is designed to be compatible with existing 5G standards, requiring no additional over-the-air feedback. The process leverages the spatial degrees of freedom already present in phased arrays to mitigate interference through three distinct stages.
- Initial Beam Selection: The system performs standard cellular alignment procedures to identify the coarse directions for transmit and receive links.
- Neighborhood Measurement: The node explores a "spatial neighborhood"—small angular shifts (typically 1–2 degrees) around the initial beams—to measure the Interference-to-Noise Ratio (INR).
- Joint Selection: The system solves an optimization problem to find a pair of transmit and receive beams that meet a target interference threshold while staying as close as possible to the original high-gain directions.
A critical component of STEER is an efficient search strategy (Algorithm 1) that minimizes measurement overhead. By sorting candidate beam pairs based on their angular deviation from the ideal SNR-maximizing direction and stopping once a pre-defined SI threshold is met, the system avoids exhaustive searching, often measuring less than 20% of possible combinations.
Experimental Results and Discussion
We evaluated STEER using a hybrid approach combining real-world measurements from an industry-grade 28 GHz phased array platform (16x16 UPAs) and system-level simulations.
- Interference Mitigation: Experimental data shows that shifting beams by as little as one degree—well within the main lobe of a narrow mmWave beam—can create deep "nulls" in the SI profile. STEER leverages these variations to reduce SI by more than 20 dB compared to conventional beam selection methods.
- System Performance: In Monte Carlo simulations of an Integrated Access and Backhaul (IAB) node, STEER improved the Signal-to-Interference-plus-Noise Ratio (SINR) by over 10 dB. This improvement directly translates to higher spectral efficiency and more robust links, even in the presence of cross-link interference from neighboring nodes.
- Mitigation vs. Cancellation: The results suggest that smart beam selection alone can push self-interference near or below the noise floor. This could potentially render complex analog/digital cancellation hardware unnecessary for many mmWave deployments.
Conclusion
STEER demonstrates that the spatial degrees of freedom inherent in mmWave phased arrays can be effectively harnessed for self-interference mitigation. By making minor adjustments to beam steering, full-duplex systems can achieve performance levels that previously required complex and expensive cancellation hardware. Future work will focus on extending STEER to dynamic urban environments with significant multi-path reflections and multi-user scenarios.
Summary updated